80 EN TROUBLESHOOTING
Before requesting service for a problem, use this chart and see if |
| Playback (DVD Deck) | ||
you can solve the trouble yourself. Small problems are often easily |
|
|
| |
solved, and this can save you the trouble of sending your unit off |
|
|
| |
| The DVD deck cannot be operated. | |||
for repair. |
| |||
| ● The DVD deck is not selected. | |||
Initializing (DVD Deck Only) |
| |||
| ]Press VHS/DVD on the unit repeatedly or DVD on the remote | |||
|
| control so that the DVD lamp lights up on the unit. | ||
Malfunction occurs on the unit. |
|
|
| |
| Images do not appear on the TV screen. | |||
]Press 1 to turn off the unit, press and hold 1, then press 8 |
| |||
| ● The TV receiver’s channel selector is not set to the AV mode. | |||
for two seconds or more. |
| |||
| ]Set the TV to its AV mode. | |||
General |
| |||
| ● When interlace scanned program is played back, progressive | |||
|
| |||
|
| scan mode is selected. | ||
|
| ]Press and hold PROGRESSIVE SCAN until disappears from | ||
No power is supplied to the unit. | ||||
| the front display panel. ( pg. 74) | |||
● The AC power plug is disconnected from the AC outlet. |
| |||
|
|
| ||
]Connect the AC power plug to the AC outlet securely. |
| Playback does not start or stop immediately after playback is | ||
( pg. 16 |
| started by pressing | . | |
| On the front display panel, “NO DISC” appears. | |||
|
| |||
|
|
|
| |
The disc tray cannot be opened.
]Open the disc tray by following the steps below.
1.Press 8 and 1 on the unit simultaneously.
2.Press and hold x (OPEN/CLOSE) on the unit for approximately 30 seconds until the tray is opened.
3.Remove the disc, then press x (OPEN/CLOSE). The unit shuts off.
The remote control does not work properly.
]Remove the batteries, wait for 5 minutes or more, then load the batteries again.
●The setting of the remote control code is inappropriate.
]Set the same remote control code (1, 2, 3, or 4) on both the unit and the remote control. ( pg. 70)
●The batteries are discharged.
]Replace the dead batteries with new ones.
Dubbing from the external equipment is not possible.
●The source (another video recorder, camcorder) has not been properly connected.
]Confirm that the source is properly connected.
●All necessary power switches have not been turned on. ]Confirm that all units’ power switches are turned on.
●The setting of the input channel position is inappropriate. ]Select the input channel position
corresponds to the input terminal connected to the external equipment. ( pg. 43)
The
]Set “SUPERIMPOSE” to “OFF”. ( pg. 73)
The unit does not operate.
●The disc is loaded upside down.
]Place the disc on the disc tray with the playback surface facing down. ( pg. 11)
●A disc not being compatible with the unit is loaded. ]Load a playable disc on the unit. ( pg. 8)
●A dirty disc is loaded.
]Clean the disc. ( pg. 11)
●Defective disc is loaded.
]Replace the warped or scratched disc with a normal one.
Images are blurred or distorted when you start
]Images are blurred or distorted at the point where the playback speed changes and this is not a malfunction of the unit.
Playback does not start.
]Playback does not start for approximately 30 seconds after recording is stopped and this is not a malfunction of the unit.
●There are cases when the operation is prohibited on the disc.
●Lightning or static electricity may cause malfunction of the unit. ]Press 1 to turn the power off, then press the button again to
turn the power on.
The remote control of a JVC TV will not operate the unit.
●The setting of the remote control code is inappropriate. ]To operate the unit using a JVC TV remote control, set the
remote control code of the unit to “1” (Default: “3”). ( pg. 70)