JVC DR-MV5S Only, To Make The Disc For On-Disc Timer Programing, Cable Box and DBS Receiver Users

Press DVD so that the DVD lamp lights up on the unit.

TIMER RECORDING EN 33

	On-Disc Timer Programing (DVD Deck		● To advance/go back the start time in 30-min. increments, press and
			hold rt.
	Only)		7 Press w e to select “STOP”, then press rt to set the desired
			stop time.
			● Each press of rt advances/goes back the stop time in 1-min.
			increments.
			● To advance/go back the stop time in 30-min. increments, press and
			hold rt.
On-Disc Timer Programing is a function used with discs that are			8 Press w e to select “CH”, then press rt to select the desired
			channel.
especially intended for a specific program. The disc is then
			9 Set “DAILY/WEEKLY” option.
programed for a program you always watch every day or every
week. Since older programs are automatically overwritten, a single			● Refer to step 6 in “VCR Plus+® Timer Programing” ( pg. 31).
DVD-RAM/RW (VR mode) disc can be used without worrying			● It is necessary to set “DAILY/WEEKLY” option for On-Disc Timer
			Programing. ( pg. 31, “Weekly/Daily Recording”)
about how much recording capacity remains. ( pg. 34)
			10 Set the other recording options as required.
You can program each disc to timer-record as many as
8 programs.			● You can select XP, SP, LP, EP or FR480 mode for “REC MODE”.
			However, you cannot select FR (JUST), FR60–FR360 and FR420.
● Make sure that the unit’s built-in clock is set properly.			● Refer to step 6 in “VCR Plus+® Timer Programing” ( pg. 31).
● Turn on the unit.			● It is not possible to use the Free Rate function. ( pg. 60)
● Turn on the TV and select the AV mode.			11 Press ENTER to access the Program Confirmation screen.
● Slide the TV/DVD switch to DVD.			12 Press ENTER to complete timer programing.
			● To program another timer, repeat steps 3 – 12.
ATTENTION:
● On-Disc Timer Programing is possible only with the disc for On-			Cable Box and DBS Receiver Users
		Disc Timer Programing.	To timer-record a satellite broadcast using the On-Disc Timer
● If data is recorded on a disc for On-Disc Timer Programing using a			Programing function:
		unit from another manufacturer, On-Disc Timer Programing may no	A Perform “On-Disc Timer Programing (DVD Deck Only)”.
		longer function properly.	B Set the cable box or DBS receiver to the appropriate channel
			before the selected program begins.
			C Select “L-1” in step 8.
			D Leave the cable box or DBS receiver’s power on.
			To Timer-record The Program With The Programed Disc

DVD

1 Load a programed disc.

2 Press TIMER #. The unit turns off and “ ” appears on the front display panel. The DVD timer lamp also lights up on the unit and the unit is automatically turned off.

●To disengage the timer mode, press TIMER # again.

NOTES:

PROG ENTER

TIMER

● On-Disc Timer Programing is not possible on a DVD-RW disc

formatted in video mode. (
pg. 78)

● The information of a program recorded with On-Disc Timer

Programing is not stored in the library. (
pg. 67)

● The play list is not created for the programs recorded with On-Disc

rtwe

To Make The Disc For On-Disc Timer Programing

1 Load a recordable disc.

2

3 Press PROG to access the Program Check screen.

4 When On-Disc Timer Programing is made for the first time on the disc

Press rt to select “DISC TIMER PRGM”, then press ENTER.

●When some programs are recorded on the disc, a caution message appears. In such a case, backup the programs as required, then format the disc before making On-Disc Timer Programing. (
pg. 78)

When On-Disc Timer Programing has already been made on the disc

Press rt to select “DISC NEW TIMER PROGRAM”, then press

ENTER.

5 Press rt to set the desired date.

●The current date appears on the TV screen. The date you enter appears in its place.

Timer Programing. (
pg. 65)

● Basic Recording (
pg. 28), VCR Plus+ Timer Programing

(
pg. 31), Manual Timer Programing (
pg. 32) are not possible on

the On-Disc Timer programed disc.

● The beginning of a program may not be recorded. Also, if the 1st

program’s recording stop time and the 2nd program’s recording start

time is the same, the ending of the 1st program may not be recorded.

● If there is a power cut while recording, the recordings before the

power cut are not guaranteed.

6 Press w e to select “START”, then press rt to set the desired start time.

●Each press of rt advances/goes back the start time in 1-min. increments.