Bostitch SB-150SX manual Tool Specifications

Page 4

TOOL SPECIFICATIONS

All screws and nuts are metric.

MODEL

TOOL ACTUATION

LENGTH

HEIGHT

WIDTH

WEIGHT

SB-1842BN

Sequential Trip

9.25”

8.5”

2”

2.38 lbs.

SB-1850BN

Sequential Trip

9.25”

9.5”

2”

2.69 lbs.

SB-150SX

Sequential Trip

9.50”

8.75”

2”

2.65 lbs.

SB-1664FN

Sequential Trip

11.25”

11.50”

3”

4.03 lbs.

SB-125BN

Sequential Trip

9.25”

8”

2”

2.12 lbs.

SB-2IN1

Sequential Trip

9.25”

8.5”

2”

2.38 lbs.

 

 

 

 

 

 

FASTENER SPECIFICATIONS:

TOOL MODEL

BRAD SERIES

GAUGE

FASTENER RANGE

SB-125BN

BT1300

18

5/8” - 1-1/4”

SB-1842BN

BT1300

18

5/8” - 1-5/8”

SB-1850BN

BT1300

18

5/8” - 2”

SB-2 IN 1

BT1300

18

5/8” - 1-5/8”

TOOL MODEL

STAPLE SERIES

CROWN WIDTH

FASTENER RANGE

SB-150SX

SX5035

5-6mm

1/2” - 1-1/2”

SB-2 IN 1

SX5035

5-6mm

1/2” - 1-1/2”

TOOL MODEL

NAIL SERIES

GAUGE

FASTENER RANGE

SB-1664FN

SB16

16

1” - 2-1/2”

TOOL AIR FITTING:

These tools use a free-flow connector plug, 1/4 N.P.T. The inside diameter should be

.200” (5mm) or larger. The fitting must be capable of discharging tool air pressure when disconnected from the air supply.

OPERATING PRESSURE:

70 to 100 p.s.i.g. (4.9 to 7.0 kg/cm2). Select the operating pressure within this range for best fastener performance.

DO NOT EXCEED THIS RECOMMENDED OPERATING PRESSURE.

OPERATION

BOSTITCH OFFERS TWO TYPES OF OPERATION.

CONTACT TRIP

The common operating procedure on “Contact Trip” tools is for the operator to contact the work to actuate the trip mechanism while keeping the trigger pulled, thus driving a fastener each time the work is contacted. This will allow rapid fastener placement on many jobs, such as sheathing, decking and pallet assembly. All pneumatic tools are subject to recoil when driving fasteners. The tool may bounce, releasing the trip, and if unintentionally allowed to recontact the work surface with the trigger still actuated (finger still holding trigger pulled) an unwanted second fastener will be driven.

SEQUENTIAL TRIP

The Sequential Trip requires the operator to hold the tool against the work before pulling the trigger. This makes accurate fastener placement easier, for instance on framing, toe nailing and crating applications. The Sequential Trip allows exact fastener location without the possibility of driving a second fastener on recoil, as described under “Contact Trip”. The Sequential Trip Tool has a positive safety advantage because it will not accidentally drive a fastener if the tool is contacted against the work – or anything else – while the operator is holding the trigger pulled.

MODEL IDENTIFICATION:

Refer to Operation Instructions on page 9 before proceeding to use this tool.

CONTACT TRIP

Identified by:

BLACK

SEQUENTIAL TRIP

Identified by:

GRAY

-4-

Image 4
Contents Finish Tools Herramientas DE Acabado Outils DE Finition SB-2IN1Introduction IndexSafety Instructions AIR Supply and ConnectionsLoading Tool OperationTool Specifications AIR Supply and Connections LubricationLoading the SB-1842BN/SB-1850BN/SB-2IN1/SB-125BN To Prevent Accidental InjuriesLoading the SB-150SX Loading the SB-1664FN Load NailsTool Operation OperationContact Trip Operation Sequential Trip OperationTool Operation Check Tool Must not CycleTool Must Cycle BOSTITCH, INCReplacement Parts Assembly Procedure for SealsAIR SUPPLY-PRESSURE and Volume Maintaining the Pneumatic ToolTrouble Shooting Problem Cause CorrectionFastener Control Adjustment Depth AdjustmentTo Adjust Fastener Control Adjustment Accessories Available Índice IntroducciónNota Instrucciones DE Seguridad Suministro DE Aire Y ConexionesAL Cargar LA Herramienta OperaciónMantenimiento DE LA Herramienta Especificaciones DE LA HerramientaLubricación Cómo Cargar LAS Herramientas Advertencia Para Impedir Lesiones AccidentalesCómo Cargar EL SB-150SX Cómo Cargar EL SB-1664FN Cargue LOS ClavosOperación DE Disparo POR Contacto Operación DE LA HerramientaOperación DE Disparo Secuencial Verificación DE LA Operación DE LA Herramienta Operación POR Disparo SecuencialLA Herramienta no Debe Efectuar SU Ciclo LA Herramienta SÍ Debe Efectuar SU CicloPresión Y Volumen DEL Suministro DE Aire Mantenimiento DE LA Herramienta NeumáticaPartes DE Reemplazo Procedimiento DE Ensamble Para LOS SellosProblema Diagnóstico DE FallaAccesorios Disponsibles Para Ajustar EL Ajuste DEL Control DE SujetadoresRemarque SommaireBostitch Consignes DE Sécurité Alimentation EN AIR Comprimé ET RaccordementChargement DE L’APPAREIL FonctionnementCaractéristiques DE L’APPAREIL Entretien DE L’APPAREILOpération Alimentation EN AIR Comprimé ET Raccordement LubrificationChargement DES SB-1842BN/SB-1850BN/ SB2IN1/SB-125BN Pour Prévenir UN AccidentChargement DU SB-150SX Chargement DU SB-1664FN Mode D’EMPLOI Fonctionnement DE L’APPAREILAvant DE Manipuler OU D’UTILISER CET Outil Déclenchement À LA VoléeVérification DU Système DE Déclenchement Système DE Sécurité À LA Volée C.TSystème DE Sécurité AU COUP-PAR-COUP ’APPAREIL NE Doit PAS SE DéclencherPièces DE Rechange Alimentation D’AIR Pression VolumeProcédure D’ASSEMBLAGE DES Garnitures Problèmes DE Fonctionnement Problème CauseAccessoires Disponibles