Lincoln Electric SVM134-A Auxiliary Power, Table B.1 Range Settings for Wire SIZE/SPEED

Page 24

B-10

B-10

OPERATION

Return to Section TOC

TO USE THE CLASSIC I FOR DC WIRE FEED WELDING (CONSTANT VOLTAGE) WITH WIRE FEED MODULE:

1.Connect the LN-25 Wire Feeder. Follow the instal- lation instructions provided with the wire feeder.

2.Set the wire feeder and Classic I for CV operation.

3.Start the engine. See Engine Operation in this section of the manual.

4.Set the Idler Switch to "AUTO."

5.Set the CURRENT RANGE SELECTOR to a set- ting appropriate for your wire size and wire feed speed. See Table B.1 for recommended settings.

6.Set the VOLTAGE ADJUSTMENT to the setting that gives the best arc characteristics for the range selected.

7.Pull the gun trigger.

Return to Section TOC

Return to Section TOC

Return to Section TOC

Return to Master TOC

Return to Master TOC

Return to Master TOC

Return to Master TOC

TABLE B.1

RANGE SETTINGS FOR WIRE SIZE/SPEED

Diameter (inches)	Wire Speed Range	Appropriate Current Range
	(inches/minute)
.035	80-110	75 to 120 Amps
.045	70-130	120 to 170 Amps
.068	40-90	125 to 210 Amps

AUXILIARY POWER

WARNING

Be sure that any electrical equipment plugged into the generator DC power receptacle can withstand a ±10% voltage variation.

The DC auxiliary power, supplied as a standard, has a rating of 1.75 kw of 120V DC power.

The rating of 1.75 kw permits a maximum continuous current of 15 amps to be drawn from the 120 volt recep- tacle.

An optional power plug kit is available. See the

Accessories section of this manual.

CLASSIC I

Image 24

Contents Classic I TM Safety California Proposition 65 WarningsElectric Shock can kill Welding Sparks can cause fire or explosion IiiPrécautions DE Sûreté Sûreté Pour Soudage a L’ArcMaster Table of Contents for ALL Sections Table of Contents Installation Section Installation Technical Specifications ClassicSafety Precautions Location and VentilationStoring PRE-OPERATION Engine Service Cooling System MufflerExhaust Spark Arrester TrailersMachine Grounding Figure A.1 Ground Stud LocationAuxiliary Power Receptacle PLUGS, and HAND-HELD Equipment Electrical Output ConnectionsWelding Cable Connections Cable size for combined lengthClassic Table of Contents Operation Section Safety Instructions OperationOperating Instructions Operational Features and Controls Recommended ApplicationsWelder GeneratorControls and Settings WELDER/GENERATOR ControlsControl of Welding Current Figure B.2 Current ControlsGasoline Engine Controls Return Section TOCEngine Operation Before Starting the EngineStarting the Engine Stopping the Engine Cold Weather StartingBREAK-IN Period Welding Operation After you finish weldingAuxiliary Power Table B.1 Range Settings for Wire SIZE/SPEEDTable of Contents Accessories OPTIONS/ACCESSORIES Semiautomatic Welding AccessoriesConnection of Lincoln Electric Wire Feeders Wire Feed Module see Figure C.1Connection of the LN-25 to Classic I Across the ARC withClassic Table of Contents Maintenance Safety Precautions Routine and Periodic Maintenance Engine MaintenanceFigure D.1 OIL Drain and Refill MAX MIN Figure D.2A Engine Coolant Drain Plug After cleaning or when installing a new spark plug Gap Specifications 0.032 inch .8 mmSet the terminal gap with a feeler gauge or gapping Tool. See Figure D.4Battery Maintenance Classic I charging system is NegativeWELDER/GENERATOR Maintenance Return to Section Return to Section TOCIdler Maintenance Figure D.5 Major Component Locations Classic Table of Contents Theory of Operation Section BATTERY, STARTER, Engine Alternator and OIL Switch Circuit Theory of OperationGeneral Description ENGINE, Main Generator Armature and Frame and DC Exciter Excitation FlashingMain SHUNT, Interpole and Series Coils Fine Current Adjustment Current Range SelectorEngine Idler Circuit DC Generator Machines Return to Section TOC Table of Contents Troubleshooting & Repair Section Troubleshooting & Repair HOW to USE Troubleshooting GuidePC Board Troubleshooting Procedures PC Board can be damaged by static electricityTroubleshooting Guide Observe Safety GuidelinesDetailed in the beginning of this manual Shunt Field Winding Test Main Generator Throttle Adjustment Test Output Problems Function Problems Troubleshooting & Repair Engine Problems Welding Problems DC Exciter Test Test DescriptionMaterials Needed Test Procedure DC Exciter TestFigure F.2 Exciter Cover Removal Small Flex Lead Solid Shunt Coil and Series Coil Resistance TestsIdler Solenoid Test Troubleshooting & Repair Main Generator Shunt Field Winding Test Main Generator Shunt Field Winding Test Figure F.6 Plug P10 PIN Assignments TAB Engine Throttle Adjustment Test Engine Throttle Adjustment Test Strobe Tach MethodEngine Throttle Adjustment Test Adjust High IdleAdjust Low Idle Flashing the Fields DescriptionProcedure Flashing the FieldsFigure F.11 Brush HOLDER/BATTERY Jumper Connections Scope Settings Normal Open Circuit Voltage Waveform 115VDC SupplyHigh Idle no Load Fine Current Control Rheostat AT Maximum Normal Open Circuit DC Weld Voltage Waveform Machine Loaded Selector Switch AT Maximum Typical DC Weld Voltage WaveformDC Exciter Armature and Field Coils Removal and Replacement DC Exciter Armature Removal Procedure ReassemblyDC Exciter Armature and Field Coils Field Coils Removal Procedure Perform the DC Exciter Armature Removal ProcedureMain Generator Frame Removal and Replacement Replacement Main Generator Frame Removal Bolt / NUTPerform the DC Exciter Armature Removal Figure F.16 Selector Switch Lead Removal Terminal LeadFigure F.18 Choke Control Cable Removal Loosen Here Main Generator Frame Removal Figure F.20 Front Panel Fastener Removal Troubleshooting & Repair Feet Remove Mounting NUTS, Washers BoltsPerform the DC Exciter Armature Reassembly Procedure Main Generator Armature Removal and Replacement Main Generator Armature Removal Armature is now free to be removed from the engineDC Auxiliary Power Receptacle Output Retest After RepairEngine Output Welder DC OutputElectrical Diagrams Section Electrical Diagrams Wiring Diagram ClassicWire Feed Module Wiring Diagram Wiring Diagram Wire Feed ModuleSchematic Idler PC Board 16990 MPC Board Assembly Idler PC Board Idler