Lincoln Electric SVM134-A service manual Feet, Remove Mounting NUTS, Washers Bolts

Page 88

Return to Section TOC

Return to Section TOC

Return to Section TOC

Return to Section TOC

Return to Master TOC

Return to Master TOC

Return to Master TOC

Return to Master TOC

F-44

F-44

TROUBLESHOOTING & REPAIR

MAIN GENERATOR FRAME REMOVAL

AND REPLACEMENT (continued)

FIGURE F.23 – MAIN GENERATOR FEET MOUNTING

MAIN GENERATOR

FEET (2)

REMOVE MOUNTING

NUTS, WASHERS,

AND BOLTS

30.Using the 3/4” wrench, remove the frame mounting bolts, nuts, and washers from the feet of the main generator. See Figure F.23.

FIGURE F.24 – MAIN GENERATOR ENGINE MOUNTING

SLING

ENGINE / GENERATOR

MOUNTING HOLES

31. With the rope sling around the main genera-	32. Using the 9/16” wrench, remove the bolts
tor frame, carefully lift the frame a small dis-	and lock washers mounting the generator
tance. Slide the wood or steel blocks under	frame to the engine. See Figure F.24.
the engine. See Figure F.24.
CLASSIC I

Image 88

Contents Classic I TM Safety California Proposition 65 WarningsElectric Shock can kill Welding Sparks can cause fire or explosion IiiPrécautions DE Sûreté Sûreté Pour Soudage a L’ArcMaster Table of Contents for ALL Sections Table of Contents Installation Section Installation Technical Specifications ClassicLocation and Ventilation Safety PrecautionsStoring PRE-OPERATION Engine Service Cooling System MufflerExhaust Spark Arrester TrailersMachine Grounding Figure A.1 Ground Stud LocationAuxiliary Power Receptacle PLUGS, and HAND-HELD Equipment Electrical Output ConnectionsWelding Cable Connections Cable size for combined lengthClassic Table of Contents Operation Section Operation Safety InstructionsOperating Instructions Operational Features and Controls Recommended ApplicationsWelder GeneratorControls and Settings WELDER/GENERATOR ControlsControl of Welding Current Figure B.2 Current ControlsGasoline Engine Controls Return Section TOCBefore Starting the Engine Engine OperationStarting the Engine Cold Weather Starting Stopping the EngineBREAK-IN Period Welding Operation After you finish weldingAuxiliary Power Table B.1 Range Settings for Wire SIZE/SPEEDTable of Contents Accessories OPTIONS/ACCESSORIES Semiautomatic Welding AccessoriesConnection of Lincoln Electric Wire Feeders Wire Feed Module see Figure C.1Connection of the LN-25 to Classic I Across the ARC withClassic Table of Contents Maintenance Safety Precautions Routine and Periodic Maintenance Engine MaintenanceFigure D.1 OIL Drain and Refill MAX MIN Figure D.2A Engine Coolant Drain Plug After cleaning or when installing a new spark plug Gap Specifications 0.032 inch .8 mmSet the terminal gap with a feeler gauge or gapping Tool. See Figure D.4Battery Maintenance Classic I charging system is NegativeWELDER/GENERATOR Maintenance Return to Section Return to Section TOCIdler Maintenance Figure D.5 Major Component Locations Classic Table of Contents Theory of Operation Section Theory of Operation BATTERY, STARTER, Engine Alternator and OIL Switch CircuitGeneral Description Excitation Flashing ENGINE, Main Generator Armature and Frame and DC ExciterMain SHUNT, Interpole and Series Coils Current Range Selector Fine Current AdjustmentEngine Idler Circuit DC Generator Machines Return to Section TOC Table of Contents Troubleshooting & Repair Section Troubleshooting & Repair HOW to USE Troubleshooting GuidePC Board Troubleshooting Procedures PC Board can be damaged by static electricityObserve Safety Guidelines Troubleshooting GuideDetailed in the beginning of this manual Shunt Field Winding Test Main Generator Throttle Adjustment Test Output Problems Function Problems Troubleshooting & Repair Engine Problems Welding Problems Test Description DC Exciter TestMaterials Needed Test Procedure DC Exciter TestFigure F.2 Exciter Cover Removal Small Flex Lead Solid Shunt Coil and Series Coil Resistance TestsIdler Solenoid Test Troubleshooting & Repair Main Generator Shunt Field Winding Test Main Generator Shunt Field Winding Test Figure F.6 Plug P10 PIN Assignments TAB Engine Throttle Adjustment Test Engine Throttle Adjustment Test Strobe Tach MethodEngine Throttle Adjustment Test Adjust High IdleAdjust Low Idle Flashing the Fields DescriptionProcedure Flashing the FieldsFigure F.11 Brush HOLDER/BATTERY Jumper Connections Normal Open Circuit Voltage Waveform 115VDC Supply Scope SettingsHigh Idle no Load Fine Current Control Rheostat AT Maximum Normal Open Circuit DC Weld Voltage Waveform Machine Loaded Selector Switch AT Maximum Typical DC Weld Voltage WaveformDC Exciter Armature and Field Coils Removal and Replacement Reassembly DC Exciter Armature Removal ProcedureDC Exciter Armature and Field Coils Field Coils Removal Procedure Perform the DC Exciter Armature Removal ProcedureMain Generator Frame Removal and Replacement Replacement Main Generator Frame Removal Bolt / NUTPerform the DC Exciter Armature Removal Figure F.16 Selector Switch Lead Removal Terminal LeadFigure F.18 Choke Control Cable Removal Loosen Here Main Generator Frame Removal Figure F.20 Front Panel Fastener Removal Troubleshooting & Repair Feet Remove Mounting NUTS, Washers BoltsPerform the DC Exciter Armature Reassembly Procedure Main Generator Armature Removal and Replacement Main Generator Armature Removal Armature is now free to be removed from the engineDC Auxiliary Power Receptacle Output Retest After RepairEngine Output Welder DC OutputElectrical Diagrams Section Electrical Diagrams Wiring Diagram ClassicWire Feed Module Wiring Diagram Wiring Diagram Wire Feed ModuleSchematic Idler PC Board 16990 MPC Board Assembly Idler PC Board Idler