Lincoln Electric R3R-300 service manual Technical Specifications Idealarc R3R-500

Page 10

Return to Section TOC

Return to Master TOC

A-4

A-4

INSTALLATION

TECHNICAL SPECIFICATIONS - IDEALARC R3R-500

INPUT - THREE PHASE ONLY

Standard Voltage	Input Current @ Rated Output
230V	88A
460V	44A

Return to Section TOC

Return to Master TOC

Duty Cycle

100%

60%

35%

RATED OUTPUT

Amps

600

500

375

OUTPUT

Volts at Rated Amps

44

40

35

Return to Section TOC

Return to Section TOC

Return to Master TOC

Return to Master TOC

Current Range	Maximum Open Circuit Voltage
75 to 625 Amps	67 VDC

	RECOMMENDED INPUT WIRE AND FUSE						SIZES AT 60% DUTY CYCLE
							Input Wire Size		Ground Wire Size
	Input Voltage /		Fuse	Input Ampere			Type 75°C		Type 75°C
	Frequency	(Super Lag)		Rating on			Copper Wire in		Copper Ground
		or Breaker Size		Nameplate			Conduit		Wire in Conduit
	Volts/Hz						AWG (IEC) Sizes		AWG (IEC) Sizes
230/60		150		88			4 (25 mm2)		6 (16 mm2)
460/60		70		44			8 (10 mm2)		8 (10 mm2)

			PHYSICAL		DIMENSIONS
	Height		Width				Depth		Weight
	27.50 in.		22.25 in.			33.10 in.			446 lbs.
	(700 mm)		(565 mm)			(840 mm)			(202 kg)

IDEALARC R3R

Image 10

Contents Idealarc R3R-300, -400 Safety California Proposition 65 WarningsElectric Shock can kill Cylinder may explode if damaged Précautions DE Sûreté Master Table of Contents for ALL Sections Table of Contents Installation Section Installation Technical Specifications Idealarc R3R-300Technical Specifications Idealarc R3R-400 Technical Specifications Idealarc R3R-500 Lifting Safety PrecautionsSelect Suitable Location TiltingGround Connection Input ConnectionsInput Supply Connections Input Wire and Fuse Size Figure A.2 Input Power Supply ConnectionsReconnect Procedure Input Supply Connection DiagramOutput Connections STICK, TIG, AIR/CARBON ARC Cutting Return to SectionIdealarc R3R Table of Contents Operation Section OPERATIONB-2 Safety InstructionsOperating Instructions General Description Design Features and AdvantagesOperation Recommended ProcessesControls and Settings Figure B.1 Case Front ControlsOperation Welding Operation Operating StepsTable of Contents Accessories Section Factory Installed Options AccessoriesOPTIONS/ACCESSORIES Field Installed OptionsTable of Contents Maintenance Section Maintenance Routine and Periodic MaintenanceFigure D.1 General Component Locations Idealarc R3R Table of Contents Theory of Operation Section Theory of Operation Input Line Voltage Contactor and Main TransformerOutput Rectification CONTROL, and Feedback Figure E.3 Output RECTIFICATION, CONTROL, and FeedbackOptional Polarity Switch and Pocket Amptrol Circuits Protective Devices and Circuits SCR Operation Figure E.5 SCR OperationTable of Contents Troubleshooting & Repair Section Troubleshooting & Repair HOW to USE Troubleshooting GuidePC Board Troubleshooting Procedures PC Board can be damaged by static electricityTroubleshooting Guide Output ProblemsSCR/Diode Pocket Amptrol Circuit Input Contactor Output Problems Welding Problems Description Materials NeededTest Procedure Input Contactor TestRemoved Test for Contact Continuity Description Figure F.3 DC Coil Input Contactor Connections Removed Control Transformer T2 Voltage Test Control Transformer T2 Voltage Test Figure F.5 Control Transformer and Lead LocationsTroubleshooting & Repair Main Transformer T1 Voltage Test Main Transformer T1 Voltage Test Figure F.8 Main Secondary Lead Test Points Phase Angle Winding Test Table F.1Figure F.9 Control Board G2206 Test Points Static SCR/DIODE Rectifier Bridge Test Static SCR/DIODE Rectifier Bridge Test Static SCR/DIODE Rectifier Bridge Test Figure F.13 Snubber Board M15370 Plug P5 LocationSCR Test Active SCR Test Active SCR Test Active SCR Test Figure F.20 SCR Tester Circuit and SCR ConnectionsPocket Amptrol Circuit Test Pocket Amptrol Circuit Test Figure F.21 T3 Transformer and Leads Pocket AmptrolFigure F.22 Pocket Amptrol Board Plug P6 and P7 Location Figure F.23 Sensing Resistor R4 Scope Settings Maximum Output Setting no LoadNormal Open Circuit Voltage Waveform Typical Output Voltage Waveform Machine Loaded Typical SCR Gate Voltage Waveform CH1Abnormal Output Voltage Waveform ONE Output SCR not FunctioningInput Contactor CR1 CLEANING/REPLACEMENT Cleaning Procedure Input Contactor CR1 CLEANING/REPLACEMENTContactor Replacement Procedure FAN Motor and Blade Removal and Replacement FAN Motor and Blade Removal and Replacement ProcedureSCR/DIODE Rectifier Assembly Removal and Replacement SCR/DIODE Rectificer Assembly Removal and ReplacementTroubleshooting ReassemblySCR Removal and Replacement SCR Removal and Replacement Special InstructionsProcedure for the 1/2 Inch Wide Spring Figure F.29 1/2 Wide Leaf SpringClamping Procedure For 1/4-28 CAP Screws Clamping Procedure For 1/4-20 CAP ScrewsProcedure for Inch Wide SpringAfter Replacing the SCRs Mounting of Stud Type Diodes to Aluminum Heat Sinks Mounting of Stud Type Diodes to Aluminum Heat SinksMain Transformer Removal and Replacement Main Transformer Removal & Replacement Removal of Lift BailRemoval of Choke and TOP Iron Assembly Figure F.34 Choke RemovalReassembly of Transformer Coils Figure F.35 Epoxy MIX Application AreasFigure F.36 Coil Lead Placement Figure F.38 Secondary Lead Trim and Weld Detail Reassembling the Main Transformer Into the Machine Reassemble the Lift BailOpen Circuit Voltages Retest After Repair R3RInput Idle Amps and Watts Welding Output Load TestWelding Output Terminals 63/69VDC 61/66VDC Welding Output Terminals 64/72VDC 61/69VDC Idealarc R3R Electrical Diagrams Idealarc R3R Electrical Diagrams DIAGRAMSELECTRICALG-4 Idealarc R3R-400, 500-I, 500 & 600-I Wiring Diagram Pocket Amptrol Schematic Snubber Board Schematic & Layout R3R-300 Control PC Board R3R-400 Control PC Board R3R-500 Control PC Board