Lincoln Electric SVM170-A service manual Installation

Page 10

	A-4	INSTALLATION	A-4
Return to Section TOC	Return to Master TOC	FIGURE A.1 — DUAL VOLTAGE MACHINE INPUT CONNECTIONS.
Return to Section TOC	Return to Master TOC
Return to Section TOC	Return to Master TOC

	3.	The 208/230 volt 60 Hz model POWER MIG is	4. Using the instructions in Figure A.3, have a qual-
		shipped with a 10 ft. input cable and plug con-	ified electrician connect the receptacle or cable to
		nected to the welder. A matching receptacle is	the input power lines and the system ground per
		supplied with the machine. Mount the receptacle	the U.S. National Electrical Code and any applic-
		in a suitable location using the screws provided.	able local codes. See Technical Specifications
		Be sure it can be reached by the plug on the input	at the beginning of this chapter for proper wire
TOC		cable attached to the welder. Mount with the	sizes. For long runs over 100 feet, larger copper
	TOC	grounding terminal at the top to allow the power	wires should be used. Fuse the two hot lines with
	TOC	cable to hang down without bending.	super lag type fuses as shown in the following dia-
Section	Master	equipped with a plug, an input cable, or a	input cable connects this contact to the frame of
			gram. The center contact in the receptacle is for
		The 230/460/575 volt 60 Hz model is not	the grounding connection. A green wire in the
to	to	receptacle.	the welder. This ensures proper grounding of the
Return	Return		welder frame when the welder plug is inserted into
Return	Return		the receptacle.
			the receptacle.

Return to Section TOC

Return to Master TOC

POWER MIG 255C

Image 10

Contents Power MIG 255C Safety California Proposition 65 WarningsElectric Shock can kill Welding Sparks can cause fire or explosion IiiPrécautions DE Sûreté Sûreté Pour Soudage a L’ArcMaster Table of Contents For ALL Sections Installation Table of Contents Installation SectionTechnical Specifications Power MIG 255C Input POWER, Grounding and Connection Diagrams Safety PrecautionsUncrating the Power MIG 255C LocationInstallation Figure A.2 Triple Voltage Machine Input Connections Auxiliary Power Receptacles GUN and Cable InstallationShielding GAS Table of Contents Operation Section OperationOPERATIONB-2 Wear eye, ear and body protec- tionWelding Capability Product DescriptionRecommended Processes and Equipment LimitationsWire Drive Roll Wire Size Conversion PartsDescription of Controls Wire Reel Loading Readi REELS, Spools or Coils Procedure for ChangingDrive and Idle Roll Sets Wire Drive Configuration Feeding Wire ElectrodeIdle Roll Pressure Setting To Start the WelderFigure B.4 Instructions to Enter Fast RUN-IN When Timer Option is not installedInstructions to Enter Slow RUN-IN Making a WeldFAN Control Avoiding Wire Feeding ProblemsWire Feed Overload Protection Input Line Voltage ProtectionWelding Thermal Overload Protection Overcurrent ProtectionAccessories Table of Contents Accessories SectionK363P READI-REEL Adapter Drive Roll KitsMagnum GUN Connection KIT Dual Cylinder Mounting KIT K1702-1K1738-1 Spool Gun Hanger Accessory Operating Instructions for Timer KITConnecting the Spool GUN to the Power MIG 255C Spool GUNMaking a Weld with the Prince XL Spool GUN Making a Weld with the Magnum SG Spool GUNSG Spool Gun Wire Feed Speed Power MIG Maintenance Table of Contents Maintenance SectionContact TIP and GAS Nozzle Installation GUN Tubes and Nozzles General MaintenanceGUN Cable Cleaning Liner Removal and ReplacementGUN Handle Disassembly Table D.1MAINTENANCED-4 English Metric DescriptionTable of Contents Theory of Operation Section Theory of OperationInput Line Voltage Main TransformerOutput Rectification Feedback ControlConstant Voltage Output Figure E.4 Constant Voltage OutputWire Drive Motor FeedbackWire Feed Overload Protection Thermal and Overload ProtectionSCR Operation Figure E.6 SCR OperationPower MIG 255C Troubleshooting and Repair Table of Contents Troubleshooting and Repair Section2TROUBLESHOOTING and REPAIRF-2 HOW to USE Troubleshooting GuidePC Board Troubleshooting Procedures Troubleshooting Guide Output ProblemsTrolyte in these capacitors is Problems Possible AreasSymptoms Misadjustments Course of Action Toxic. Avoid contact with anyPerform the SCR Rectifier Function Problems Wire Feeding Problems Welding Problems Welding Problems Test Description Test ProceduresMain Transformer Test Materials NeededTest Procedure ON/OFF Power Switch will be hot during these tests115VAC 16J5 8J5206 3J5 Rectifier Diode Bridge Test 16TROUBLESHOOTING and REPAIRF-16 Figure F.2 G3521 Rectifier Diode Bridge Location208 206 28 VAC 209 354 206 36 VDCPower MIG 255C Static SCR Rectifier Assembly Test Static SCR Rectifier Assembly Test Active SCR Rectifier Assembly Test Power MIG 255C Active SCR Rectifier Assembly Test Active SCR Rectifier Assembly Test Figure F.7 Location Leads X2 Figure F.8 Wire Drive Motor and Tachometer Feedback Test Wire Drive Motor and Tachometer Feedback Test 4J1Test for Supply Voltage to Tachometer 515B 206B 15 VDC 5J1 1J1Test for Feedback Voltage to Control Board 555 206B To 3.5 VDC 6J1 1J1Normal Open Circuit Voltage Waveform VoltsMachine Loaded to 250 Amps AT 26 VDC Scope Settings Typical Output Voltage Waveform Machine LoadedMachine Loaded to 220 Amps AT 22 VDC Scope Settings Troubleshooting and Repair Typical SCR Gate Voltage Waveform Power MIG 255C Control PC Board Removal and Replacement Component Replacement ProceduresDescription Removal and Replacement ProcedureFigure F.11 Control Board Mounting Power MIG 255C Wire Drive Assembly Removal and Replacement Wire Drive Assembly Removal and Replacement Procedure Power MIG 255C SCR Output Rectifier Removal and Replacement SCR Output Rectifier Removal and Replacement Figure F.15 Right Heat Sink Lead Disconnection Power MIG 255C Capacitor Bank Removal and Replacement Capacitor Bank Removal and Replacement Main Transformer and Output Choke Removal and Replacement 52TROUBLESHOOTING and REPAIRF-52 Main Transformer and Output ChokeTOC Power MIG 255C FAN Motor Assembly Removal and Replacement FAN Motor Assembly Removal and Replacement Open Circuit Voltage Wire Speed RangeRetest After Repair Input Volts/HertzPower MIG 255C Electrical Diagrams Section Section G-1Electrical Diagrams Wiring Diagram Entire Machine Code 11192 L12464Wiring Diagram Entire Machine Code 11218 L12506 Schematic Entire Machine G4752 Schematic Control PC Board G4823-2D1 Sheet Electrical Diagrams Electrical Diagrams PC Board Assembly Control G4824-2D1 Item Used with QTY Part Number DescriptionSchematic Display PC Board L10951 PowermigPC Board Assembly Display L10952 Lincoln Electric COSVM Error Reporting Form