Lincoln Electric IM819-B manual Engine Adjustments, Overspeed is Hazardous, Slip Rings, Battery

Page 26

D-3

MAINTENANCE

D-3

ENGINE ADJUSTMENTS

OVERSPEED IS HAZARDOUS

WARNING

The maximum allowable high idle speed for this machine is 3750 RPM, no load. Do NOT tamper with governor components or setting or make any other adjustments to increase the maximum speed. Severe personal injury and damage to the machine can result if operated at speeds above maximum.

------------------------------------------------------------------------

Adjustments to the engine are to be made only by a Lincoln Service Center or an authorized Field Service Shop.

SLIP RINGS

A slight amount of darkening and wear of the slip rings and brushes is normal. Brushes should be inspected when a general overhaul is necessary.If brushes are to be replaced, clean slip rings with a fine emery paper.

CAUTION

Do not attempt to polish slip rings while engine is running.

------------------------------------------------------------------------

WARNING

GASES FROM BATTERY can explode.

Keep sparks, flame and cigarettes away from battery.

To prevent EXPLOSION when:

INSTALLING A NEW BATTERY - disconnect negative cable from old battery first and connect to new battery last.

CONNECTING A BATTERY CHARGER - Remove bat-

tery from welder by disconnecting negative cable first, then positive cable and battery clamp. When rein- stalling, connect negative cable last. Keep well venti- lated.

USING A BOOSTER - connect positive lead to battery first then connect negative lead to engine foot.

BATTERY ACID CAN BURN EYES AND SKIN.

Wear gloves and eye protection and be careful when working near battery. Follow instructions printed on battery.

BATTERY

1.When replacing, jumping, or otherwise connecting the battery to the battery cables, the proper polarity must be observed. Failure to observe the proper polarity could result in damage to the charging circuit. The positive (+) battery cable has a red terminal cover.

2.If the battery requires charging from an external charger, disconnect the negative battery cable first and then the positive battery cable before attaching the charger leads. Failure to do so can result in damage to the internal charger components. When reconnecting the cables, connect the positive cable first and the negative cable last.

HARDWARE

Both English and Metric fasteners are used in this welder.

ENGINE MAINTENANCE PARTS

 

 

KOHLER C20S

HONDA GX620KI

ROBIN / SUBARU EH64

 

 

 

 

 

 

 

KOHLER 1205001

HONDA

ROBIN / SUBARU

 

Oil Filter

FRAM PH3614*

15410-ZJ4-999A

248-65801-00, FRAM PH4967

 

 

 

 

 

 

Air Filter

KOHLER 4708303

HONDA

ROBIN / SUBARU

 

Element

FRAM CA79

17210-ZJ1-841

263-32610-A1

 

 

 

 

 

 

Air Filter

KOHLER 2408302

HONDA

N/A

 

Pre-Cleaner

 

17218-ZJ1-840

 

 

 

 

 

 

 

Fuel Filter

KOHLER 2505002

HONDA

ROBIN / SUBARU

 

 

FRAM G1

16910-ZE8-015

011-00600-20

 

 

 

 

 

 

Spark Plugs

CHAMPION RC12YC

CHAMPION -J16CR-U

ROBIN / SUBARU

 

(Resistor

(.030GAP)

NGK-ZGR5A

X65-01407-30

 

Type)

 

030in, (76 mm) Gap

NGK-BPR4EY

 

 

 

 

 

*Oil capacity increases from 2.0 Qts. to 2.1 Qts. when using this filter.

RANGER 10,000

Image 26
Contents Ranger 10,000 Safety Electric Shock can kill Cylinder may explode if damaged Précautions DE Sûreté Thank You Table of Contents Installation Height Width Depth WeightSafety Precautions OIL Vehicle MountingFuel AWG FallingWelder Output Connection of the LN-25 to the RangerConnection of K930-2 TIG Module to the Ranger 10,000 Motor Starting 120/240 Volt Dual Voltage ReceptacleDuplex Receptacles Not USE These Devices With a Ranger 10,000 Electrical Device USE with the Ranger 10,000These Devices Without Additional Resistive Type Loads Standby Power Connections Auxiliary Power While WeldingSimultaneous Welding and Power Installation Connection of Ranger 10,000 to Premises WiringOperation Safety PrecautionsEngine Switch Ranger 10,000 Approximate Fuel Consumption Polarity SwitchRange Switch Control DialStarting the Engine STARTING/SHUTDOWN InstructionsBREAK-IN Period Stopping the EngineStick Constant Current Welding Wire Feed Welding Processes Constant VoltageWelding Process TIG Constant Current WeldingStick Auto Accessories K1745-1 GAS Cylinder HolderTIG Welding Wire FeedStick Plasma CuttingEngine OIL Refill Capacities MaintenanceEngine OIL Change Kohler HondaAIR Cleaner and Other Maintenance OIL Filter ChangeOverspeed is Hazardous Engine AdjustmentsBattery Slip RingsTroubleshooting HOW to USE Troubleshooting GuideTroubleshooting Troubleshooting Diagrams Ranger 10,000 Kohler CSA Wiring Diagram forRanger 10,000 Honda Wiring Diagram for Code M20431 Engine Welder Kohler , Honda and Robin / Subaru Precaucion Warnung