Lincoln Electric IM819-B manual Stick, Wire Feed, TIG Welding, Plasma Cutting

Page 23

C-2

ACCESSORIES

C-2

RECOMMENDED EQUIPMENT

STICK

K704 Accessory Kit - For Stick Welding. Includes 35 ft (10.7m).

•2/0 AWG electrode cable, 30 ft. (9.1m)

•2/0 AWG work cable with lugs, headshield, filter plate, work clamp, and electrode holder. 400 amp capacity.

K875 Accessory Kit - For stick welding. Includes 20 Ft. (6.1m). #6 electrode cable with lug, 15 Ft. (4.6m) #6 work cable with lugs, headshield, filter plate, work clamp, and electrode holder and sample pack of mild steel electrode. 150 amp capacity.

WIRE FEED

K449 LN-25 - Includes internal contactor for across the arc operation (no control cable). Provides “cold” electrode until gun trigger is pressed. Includes gas solenoid.

K1870-1 LN-15 Across the Arc

Magnum Gun and Magnum Gun Connector Kit are required for gas-shielded welding. Innershield Gun is required for gasless welding.

K126-2Magnum 350 Innershield Gun (for LN-25, LN- 15).

K1802-1Magnum 300 MIG Gun (for LN-25, includes Connector Kit).

K470-2Magnum 300 MIG Gun (for LN-15, requires

K466-10 Magnum Gun Connector Kit). K1500-1Gun Receiver Bushing (for LN-15, K126-2)

Note: See Wire Feeder IM Manual for appropriate

Drive Roll & Guide Tube Kits.

TIG WELDING

K1783-9-PTA-26V TIG Torch.

KP509- Magnum Parts Kit and Argon gas.

K930-2-TIG Module.

Required TIG Equipment:

K938-1 Connector Kit

K936-4 Control Cable

K814 Arc Start Switch

Optional TIG Equipment:

K939-1 Docking Kit

K937-45 Control Cable Extension

K844-1 Water Valve Kit

PLASMA CUTTING:

K1580-1-Pro-Cut 55 (Requires full KVA Adapter

K1816-1).

RANGER 10,000

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Ranger 10,000 Safety Electric Shock can kill Cylinder may explode if damaged Précautions DE Sûreté Thank You Table of Contents Height Width Depth Weight InstallationSafety Precautions OIL Vehicle MountingFuel Falling AWGWelder Output Connection of the LN-25 to the RangerConnection of K930-2 TIG Module to the Ranger 10,000 Motor Starting 120/240 Volt Dual Voltage ReceptacleDuplex Receptacles Not USE These Devices With a Ranger 10,000 Electrical Device USE with the Ranger 10,000These Devices Without Additional Resistive Type Loads Standby Power Connections Auxiliary Power While WeldingSimultaneous Welding and Power Connection of Ranger 10,000 to Premises Wiring InstallationOperation Safety PrecautionsEngine Switch Control Dial Polarity SwitchRange Switch Ranger 10,000 Approximate Fuel ConsumptionStopping the Engine STARTING/SHUTDOWN InstructionsBREAK-IN Period Starting the EngineTIG Constant Current Welding Wire Feed Welding Processes Constant VoltageWelding Process Stick Constant Current WeldingStick Auto K1745-1 GAS Cylinder Holder AccessoriesPlasma Cutting Wire FeedStick TIG WeldingKohler Honda MaintenanceEngine OIL Change Engine OIL Refill CapacitiesOIL Filter Change AIR Cleaner and Other MaintenanceSlip Rings Engine AdjustmentsBattery Overspeed is HazardousHOW to USE Troubleshooting Guide TroubleshootingTroubleshooting Troubleshooting Ranger 10,000 Kohler CSA Wiring Diagram for DiagramsRanger 10,000 Honda Wiring Diagram for Code M20431 Engine Welder Kohler , Honda and Robin / Subaru Precaucion Warnung
Top Page Image Contents