Lincoln Electric IM819-B manual Vehicle Mounting, Fuel, Oil

Page 10

A-3

INSTALLATION

A-3

3.Proper placement of the equipment on the trailer to insure stability side to side and front to back when being moved and when standing by itself while being operated or serviced.

4.Typical conditions of use, i.e., travel speed; rough- ness of surface on which the trailer will be operated; environmental conditions.

5.Conformance with federal, state and local laws(1)

(1)Consult applicable federal, state and local laws regarding specific requirements for use on public highways.

VEHICLE MOUNTING

WARNING

Improperly mounted concentrated loads may cause unstable vehicle handling and tires or other components to fail.

Only transport this Equipment on serviceable vehicles which are rated and designed for such loads.

Distribute, balance and secure loads so vehicle is stable under conditions of use.

Do not exceed maximum rated loads for compo- nents such as suspension, axles and tires.

Mount equipment base to metal bed or frame of vehicle.

Follow vehicle manufacture’s instructions.

------------------------------------------------------------------------

FUEL

Fill the fuel tank with clean, fresh, lead-free gasoline. Observe fuel gauge while filling to prevent overfilling.

WARNING

• Damage to the fuel tank may cause fire or explosion. Do not drill holes in the RANGER 10,000 base or weld to the RANGER 10,000 base.

-----------------------------------------------------------------------

OIL

LUBRICATION SYSTEM CAPACITY

(INCLUDING FILTER)

Kohler CH20S - 2.0 Quarts (1.9 Liters)

Honda GX620KI-1.9 Quarts (1.8 Liters)

Robin/Subaru EH6-1.6 Quarts (1.6 Liters)

The Ranger 10,000 is shipped with the engine crankcase filled with SAE 10W-30 oil. Check the oil level before starting the engine. If it is not up to the full mark on the dip stick, add oil as required. Make cer- tain that the oil filler cap is tightened securely. Refer to the engine Owner’s Manual for specific oil recommen- dations.

PRE-OPERATION SERVICE

CAUTION

READ the engine operating and maintenance instructions supplied with this machine.

CAUTION

BATTERY CONNECTIONS

Use caution as the electrolyte is a strong

acid that can burn skin and damage eyes.

-----------------------------------------------------------------------

GASOLINE

can cause fire or explosion.

WARNING

Stop engine while fueling.

Do not smoke when fueling.

Keep sparks and flame away from tank.

Do not leave unattended while fueling.

Wipe up spilled fuel and allow fumes to clear before starting engine.

Do not overfill tank, fuel expan- sion may cause overflow.

This welder is shipped with the negative battery cable disconnected. Make sure that the Engine Switch is in the “STOP” position and attach the disconnected cable securely to the negative battery terminal before attempting to operate the machine. If the battery is discharged and does not have enough power to start the engine, see the battery charging instructions in the Battery section.

NOTE: This machine is furnished with a wet charged battery; if unused for several months, the battery may require a booster charge. Be careful to charge the bat- tery with the correct polarity.

GASOLINE FUEL ONLY

------------------------------------------------------------------------

RANGER 10,000

Image 10
Contents Ranger 10,000 Safety Electric Shock can kill Cylinder may explode if damaged Précautions DE Sûreté Thank You Table of Contents Installation Height Width Depth WeightSafety Precautions Fuel Vehicle MountingOIL AWG FallingConnection of K930-2 TIG Module to the Ranger 10,000 Connection of the LN-25 to the RangerWelder Output Duplex Receptacles 120/240 Volt Dual Voltage ReceptacleMotor Starting These Devices Without Additional Resistive Type Loads Electrical Device USE with the Ranger 10,000Not USE These Devices With a Ranger 10,000 Simultaneous Welding and Power Auxiliary Power While WeldingStandby Power Connections Installation Connection of Ranger 10,000 to Premises WiringEngine Switch Safety PrecautionsOperation Ranger 10,000 Approximate Fuel Consumption Polarity SwitchRange Switch Control DialStarting the Engine STARTING/SHUTDOWN InstructionsBREAK-IN Period Stopping the EngineStick Constant Current Welding Wire Feed Welding Processes Constant VoltageWelding Process TIG Constant Current WeldingStick Auto Accessories K1745-1 GAS Cylinder HolderTIG Welding Wire FeedStick Plasma CuttingEngine OIL Refill Capacities MaintenanceEngine OIL Change Kohler HondaAIR Cleaner and Other Maintenance OIL Filter ChangeOverspeed is Hazardous Engine AdjustmentsBattery Slip RingsTroubleshooting HOW to USE Troubleshooting GuideTroubleshooting Troubleshooting Diagrams Ranger 10,000 Kohler CSA Wiring Diagram forRanger 10,000 Honda Wiring Diagram for Code M20431 Engine Welder Kohler , Honda and Robin / Subaru Precaucion Warnung