Friedrich HEAT&COOLING MODEL INVERTER (REVERSE CYCLE) ROOM AIR CONDITIONER WALL MOUNTED TYPE

Page 7

To Stop Operation

Press the START/STOP button (Fig. 6 R).

The OPERATION Indicator Lamp (red) (Fig. 3 5) will go out.

About AUTO CHANGEOVER Operation

AUTO: ● When AUTO CHANGEOVER operation first selected, the fan will oper- ate at very low speed for about one minute, during which time the unit detects the room conditions and selects the proper operating mode.

If the differance between thermostat setting and actual room tempera- ture is more than +4 °F Cooling or dry operation

If the difference between thermostat setting and actual room tempera- ture is within ±4 °F Monitor operation

If the difference between thermostat setting and actual room tempera- ture is more than –4 °F Heating operation

When the air conditioner has adjusted your room’s temperature to near the thermostat setting, it will begin monitor operation. In the monitor operation mode, the fan will operate at low speed. If the room tem- perature subsequently changes, the air conditioner will once again select the appropriate operation (Heating, Cooling) to adjust the tem- perature to the value set in the thermostat.

(The monitor operation range is ±4 °F relative to the thermostat set- ting.)

If the mode automatically selected by the unit is not what you wish, select one of the mode operation (HEAT, COOL, DRY, FAN).

About Mode Operation

Heating: ● Use to warm your room.

When Heating mode is selected, the air conditioner will operate at very low fan speed for about 3 to 5 minutes, after which it will switch to the selected fan setting. This period of time is provided to allow the indoor unit to warm up before begin full operation.

When the room temperature is very low, frost may form on the outside unit, and its performance may be reduced. In order to remove such frost, the unit will automatically enter the defrost cycle from time to time. During Automatic Defrosting operation, the OPERATION Indica- tor Lamp (Fig. 3 5) will flash, and the heat operation will be inter- rupted.

Cooling: ● Use to cool your room.

Dry: ● Use for gently cooling while dehumidifying your room.

You cannot heat the room during Dry mode.

During Dry mode, the unit will operate at low speed; in order to adjust room humidity, the indoor unit’s fan may stop from time to time. Also, the fan may operate at very low speed when adjusting room humidity.

The fan speed cannot be changed manually when Dry mode has been selected.

Fan: ● Use to circulate the air throughout your room.

During Heating mode:

Set the thermostat to a temperature set- ting that is higher than the current room temperature. The Heating mode will not operate if the thermostat is set lower than the actual room temperature.

During Cooling/Dry mode:

Set the thermostat to a temperature set- ting that is lower than the current room temperature. The Cooling and Dry modes will not operate if the thermostat is set higher than the actual room temperature (in Cooling mode, the fan alone will oper- ate).

During Fan mode:

You can not use the unit to heat and cool your room.

En-6

06B029_9315255037-01_En

6

2006.2.6, 10:52 AM

Image 7
Contents Español Français English Operating ManualFiche Technique ContentsSafety Precautions SpecificationsInverter Features and FunctionsIndoor Unit Operating Control Panel Fig Manual Auto button Name of PartsPreparation Operation To Stop Operation Press the START/STOP button R About Mode OperationAbout Auto Changeover Operation Timer Operation During Cooling/Dry operation Sleep Timer OperationAbout the Sleep Timer During Heating operationTypes of Air flow Direction Setting Adjusting the Direction of AIR CirculationVertical Air Direction Adjustment Press the SET button S Right-Left Adjustment Adjust the Right-Left louversTo select Swing Operation Press the Swing button T Swing OperationCoil DRY Operation Manual Auto OperationCleaning and Care Replace them by two new Air cleaning filters Install the Air cleaning filter set setInstall the two Air filters and close the Intake Grille Replacing dirty Air cleaning filtersSymptom Problem TroubleshootingSee Auto Restart Event of Power InterruptionOperating Tips Operation and PerformanceTips for saving energy Temperature and Humidity RangeCooling Mode Dry Mode Heating Mode Outdoor temperature Indoor temperature06B0299315255037-01En 2006.2.6, 1052 AM Précautions DE Sécurité SommaireInverseur Caractéristiques ET FonctionsManual Auto Nomenclature DES OrganesPréparatifs Réglage du thermostat Appuyez sur la touche SET TEMP. L Pour choisir le mode souhaitéFonctionnement Appuyez sur la touche Master Control KArrêt du climatiseur Appuyez sur la touche START/STOP R Propos du mode de fonctionnementRêt OFF et la mise en marche on par minuterie Appuyez sur la touche Timer Mode O pourFonctionnement PAR Minuterie DE Programmation ’heure d’arrêt et de mise en marche souhaitéesPendant le chauffage Fonctionnement TemporiséChangement des réglages du minuterie Propos de la minuterie à temporisateurRéglage Gauche-Droite Ajustez les Volets Gauche-Droite Réglage DE LA Direction DU Flux D’AIRPositions de réglage de direction du flux d’air Propos du fonctionnement oscillant Fonctionnement OscillantFonctionnement DU Séchage DU Serpentin Fonctionnement MANUEL-AUTOMATIQUENettoyez la poussière avec un aspirateur ou en lavant Nettoyage ET EntretienNettoyez à l’eau Remettez la grille d’admissionEntretien des filtres désodorisants Remplacement de filtres de nettoyage d’air salesRemplacez-les par deux nouveaux filtres de nettoyage d’air Remarques sur les filtres de nettoyage d’airSymptôme Problème Voyez Guide DE DépannageEn cas de coupure de courant Conseils D’UTILISATIONFonctionnement et performance Remise en marche automatiqueEnviron 5 F à 75 F Plage de température et d’humiditéConseils pour une économie d’énergie Température intérieure Environ 64 F à 90 FPage Precauciones DE Seguridad ÍndiceInversor Funcionamiento DE Vaivén Características Y FuncionesAutomática Sleep Pantalla de vaivén Swing Denominación DE LOS ComponentesPreparativos Funcionamiento supersilencioso Super Quiet FuncionamientoPara seleccionar el modo de funcionamiento Para ajustar el termostatoNotas sobre el funcionamiento de los modos NotassobreelfuncionamientodecambioautomáticoAUTOCHANGEOVERNexión OFF y del de conexión on Funcionamiento CON TemporizadorEmpleo del temporizador programable Si el aparato ya está funcionando pase al pasoDurante el funcionamiento de refrigeración/deshumectación Para cambiar los ajustes del tiempoNotas sobre el temporizador de desconexión automática Sleep Durante el funcionamiento de calefacciónTipos de ajustes de la dirección del flujo de aire Ajuste DE LA Dirección DE Circulación DEL AirePara detener el funcionamiento de deshumectación Coil DRY Funcionamiento DE VaivénFuncionamiento DE Deshumectación Coil DRY Funcionamiento Manual Y AutomáticoSaque el polvo con una aspiradora o la- vándolo Limpieza Y MantenimientoLimpie con agua Colocación de la rejilla de entradaMantenimiento de los filtros desodorizantes Sustitución de los filtros de limpieza de aire suciosSustitúyalos dos filtros de limpieza de aire nuevos Acerca de los filtros de limpieza de aireLocalización DE Averías Síntoma Problema Vea la PáginaEn el caso de una interrupción de la alimentación Consejos Para EL FuncionamientoFuncionamiento y rendimiento Reinicio automáticoConsejos para el ahorro de energía Margen de temperatura y humedad

HEAT&COOLING MODEL INVERTER (REVERSE CYCLE) ROOM AIR CONDITIONER WALL MOUNTED TYPE specifications

The Friedrich HEAT&COOLING MODEL INVERTER (REVERSE CYCLE) ROOM AIR CONDITIONER is a top-tier wall-mounted solution that stands out in the competitive landscape of air conditioning units. Designed for both cooling and heating, this versatile inverter system is engineered to deliver optimal comfort year-round, regardless of the weather conditions outside.

One of the key features of this model is its advanced inverter technology, which allows for precise temperature control. Unlike traditional air conditioners that operate at a fixed speed, the inverter technology enables the compressor to adjust its speed based on the current demands of the room. This not only enhances energy efficiency but also provides a quieter operation, making it an ideal choice for bedrooms and living spaces.

The reverse cycle functionality means that the unit can efficiently switch between heating and cooling modes. In the cooling mode, it effectively removes heat and humidity from the indoor environment, while in the heating mode, it extracts heat from the outside air and transfers it indoors, even in colder temperatures. This dual capability makes the Friedrich model incredibly versatile for homeowners.

Another significant characteristic of this air conditioner is its energy efficiency ratings, typically classified under SEER (Seasonal Energy Efficiency Ratio) and HSPF (Heating Seasonal Performance Factor). This model boasts impressive figures that can lead to substantial savings on energy bills over time, making it an eco-friendly choice that aligns with modern sustainability goals.

The air conditioner also features smart technology integration, allowing users to control the unit remotely through a mobile app. This capability provides convenience and flexibility, enabling users to adjust settings from anywhere, ensuring their space is comfortable upon arrival.

The unit's design is sleek and modern, ensuring that it blends seamlessly with various interior décor styles while occupying minimal wall space. Additionally, the filter system is designed for easy access and maintenance, ensuring that clean air is circulated throughout the room while maintaining the unit’s performance.

Overall, the Friedrich HEAT&COOLING MODEL INVERTER room air conditioner merges innovative technology, energy efficiency, and user-friendly features, making it a premier choice for residential heating and cooling needs.