Milwaukee 4270-20 manual Tool Assembly, Stop Knob Fig, Adjusting the Gib Assembly Fig

Page 7

TOOL ASSEMBLY

WARNING!

To reduce the risk of injury, always unplug tool before attaching or removing accessories or making adjustments. Use only specifically recommended accessories. Others may be hazardous.

Attaching Feed Handles and Grips (Fig. 1)

Fig. 1

1.Assemble the feed handles and grips to the hub. Tighten securely.

2.To mount the hub to either side, align the two (2) dowel pins on the hub with the holes in the pinion. Tighten the handle screw.

Stop Knob (Fig. 2)

The stop knob is designed to stop the slide from moving. To install, screw stop knob into location shown (Fig. 2).

Fig. 2

Stop knob

Adjusting the Gib Assembly (Fig. 3)

Fig. 3

To adjust the gib, loosen or tighten the gib adjustment set screws on the side of the support housing accordingly with the 3/32" hex key provided. Tightening the set screws increases friction on the slide. The gib should be set tight enough to support the weight of the drill in any position. All adjusting screws should be set to provide smooth and even travel over the entire length of slide movement.

The set screws contain a nylon patch that prevents them from moving freely. Additional adjustment of the gib may be required from time to time with extended use of the tool.

Adjusting the Support Bracket and Spacer for Depth of Cut (Figs. 4 & 5)

This unit is shipped from the factory set for 1" depth cutters (Fig. 4).

Fig. 4

Spacer

Support bracket

When using 2" depth cutters, install support bracket with spacer on bottom, as shown in Fig. 5.

Fig. 5

Spacer

Support bracket

NOTE: Do not use a spacer and support bracket with chuck adapter.

page 7

Image 7

Contents Operators Manual Page Service Work Area Safety Power Tool USE and CareElectrical Safety Personal Safety Bore Drill Cutter 4270-20 120 450 Specific Safety Rules for Electromagnetic Drill Press Volts Cat No Load Arbor Twist Only AmpsMotor/Magnet Interlock FeaturesFunctionaldescription Line LockoutExtension Cords Guidelines for Using Extension CordsRecommended Minimum Wire Gauge For Extension Cords GroundingAdjusting the Gib Assembly Fig Tool AssemblyStop Knob Fig Operation Excessive force will break magnet free Accessories MaintenanceFive Year Tool Limited Warranty UTILISATIONETENTRETIENDEL’OUTILÉLECTRIQUE Conserver CES Instructions Sécurité DU Lieu DE TravailSécurité Électrique Sécurité IndividuelleNo de Volts Tr/min à Calibre Foret Cat PictographieDispositif de verrouillage du moteur/aimant DescriptionfonctionnelleCaractéristiques Neutralisation de ligneDirectives pour l’emploi des cordons de rallonge Calibres minimaux recommandés pour Les cordons de rallongeMise À LA Terre Avertissement Cordons DE RallongeBouton d’arrêt Fig Montage DE Loutil AvertissementRéglage de l’ensemble du lardon Fig Maniement Avertissement Avertissement Accessoires Avertissement Maintenance AvertissementGarantie Limitée DE L’OUTIL DE Cinq ANS USO Y Cuidado DE LAS Herramientas Eléctricas GUA0RDE Estas Instrucciones Seguridad EN EL Área DE TrabajoSeguridad Eléctrica Seguridad PersonalVolts Rpm Diámetro Cat Sin Interior del Broca Amarra de SeguridadEnclavamiento del Motor/Imán DescripcionfuncionalCaracteristicas Bloqueo de LíneaExtensiónes Eléctricas Tierra ¡ADVERTENCIAGuías para el uso de cables de extensión Perilla de Tope Fig Ensamblaje DE LA Herramienta ¡ADVERTENCIAAjuste del Conjunto de la Contrachaveta Fig Operacion ¡ADVERTENCIA El uso excesivo de fuerza liberará el imán Accesorios ¡ADVERTENCIA Mantenimiento ¡ADVERTENCIAGarantía Limitada DE Cinco Años Notas Sawdust