Lincoln Electric 8 manual Recommended Equipment, Stick, Tig, Wire Feed

Page 24

C-2	ACCESSORIES	C-2

RECOMMENDED EQUIPMENT

STICK

K704 Accessory Kit which includes:

•Electrode Holder & Cable

•Work Clamp & Cable

•Headshield

K892-1 Remote Control Receptacle Kit and K857 Remote Control Kit are optional for remote current control.

TIG

Magnum™ TIG Torch

Magnum Parts Kit and Argon Gas

K930-2 TIG Module (requires K938-1 Contactor Kit)

K939-3 Control Cable (see Optional Equipment)

Optional:

•K939-1 Docking Kit

•K963 Hand Amptrol®

•K870 Foot Amptrol

•K892-1 Remote Control Receptacle Kit

•K915-1 Adapter Cable

WIRE FEED

K449 LN-25 - Includes internal contactor for across the arc operation (no control cable). Provides “cold” electrode until gun trigger is pressed. Includes gas solenoid. K892-1 Remote control Receptacle Kit and K444-1 Remote voltage Control Kit are required for voltage control at the feeder.

LN7-K240 Contactor Kit is required.

Magnum Gun is required for gas-shielded welding.

Innershield Gun is required for gasless welding.

RANGER 8

Image 24

Contents Safety Depends on You RangerSafety California Proposition 65 WarningsElectric Shock can kill Welding Sparks can cause fire or explosion IiiPrécautions DE Sûreté Sûreté Pour Soudage a L’ArcThank You Please Examine Carton and Equipment For Damage ImmediatelyTable of Contents Installation Height Width Depth WeightK2160-1 CSA Meets Canadian STD RangerSpecifications DC Wire Feed CV Output CV Output Range20 B 100 150 200 250 Output Amps DC Stick / TIG CC Output Output RangeInstallation Instructions Safety PrecautionsSpark Arrester Machine GroundingPre-Operation Service Welding Output CablesAWG Connection of Lincoln Electric Wire Feeders Angle of OperationHigh Altitude Operation Location / VentilationAdditional Safety Precautions Auxiliary PowerInstructions Connection of K930- TIG Module to the RangerDuplex Receptacles Motor StartingElectrical Device USE with the Ranger Type Common Electrical Devices Possible ConcernsThese Devices Without Additional Resistive Type Loads Not USE These Devices With a RangerAuxilliary Power While Welding Simultaneous Welding and PowerStandby Power Connections Connection of Ranger 8 to Premises Wiring Design Features Other FeaturesOperation General DescriptionEngine ON-OFF Switch Engine Start Push-Button SwitchOnan P216 Kohler Honda 16 H.P. Performer 20 H.P. Command Ranger 8 Approximate Fuel ConsumptionStarting/Shutdown Instructions Break-in PeriodStopping the Engine Wire Feed Welding Processes Constant Voltage Welding ProcessStick Constant Current Welding TIG Constant Current WeldingSummary of Welding Processes Stick AutoAccessories K1745-1 Single GAS Cylinder HolderWire Feed Recommended EquipmentStick TIGMaintenance Safety PrecautionsCH20S Overspeed is Hazardous Onan P216 Kohler CH20S Honda GX620Troubleshooting HOW to USE Troubleshooting GuideTroubleshooting Troubleshooting Diagrams K1418-1 Code 10373 & 10535 Ranger 8 Onan Wiring DiagramALL Case Front Components Shown Viewed from Rear K1419-1 Code 10375 & 10537 Ranger 8 Kohler Wiring Diagram ALL Case Front Components Shown Viewed from Rear K2160-1 Code 10886 Ranger 8 Honda CSA Wiring Diagram Connection of Ranger 8 to LN-7 & K240 Contactor KIT M17215-2 30-98E M17215-3 30-98E Ranger How To Read Shop Drawings New Lessons in Arc WeldingNeed Welding Training? Basic CoursePrecaucion Warnung