Lincoln Electric 305D manual Engine Welders /LN-8 Connection Diagram, S24787-6

Page 43

ENGINE WELDERS /LN-8 CONNECTION DIAGRAM

WARNING

F-5

ELECTRIC SHOCK can kill

Do not operate with panels open.

Disconnect NEGATIVE (-) Battery lead

before servicing.

Do not touch electrically live parts.

MOVING PARTS can injure

Keep guards in place.

Keep away from moving parts.

Only qualified personnel should install,use or service this equipment.

RANGER® 305D

14 PIN AMPHENOL

+ _

CAUTION:

TO LN-8 INPUT

CABLE PLUG

K595 CONTROL CABLE

TO WORK

ELECTRODE CABLE

TO WIRE FEED UNIT

DIAGRAMS

ANY INCREASE OF THE HIGH IDLE ENGINE RPM BY CHANGING THE GOVERNOR SETTING OR OVERRIDING THE THROTTLE LINKAGE WILL CAUSE AN INCREASE IN THE AC WIRE FEEDER VOLTAGE, WHICH CAN DAMAGE THE CONTROL CIRCUIT. THE ENGINE GOVERNOR SETTING IS PRE-SET AT THE FACTORY Ð DO NOT ADJUST ABOVE RPM SPECIFICATIONS LISTED IN THE ENGINE WELDER OPERATING MANUAL.

N.A. WELDING CABLES MUST BE OF PROPER CAPACITY FOR THE CURRENT AND DUTY CYCLE OF IMMEDIATE AND FUTURE APPLICATIONS. SEE OPERATING MANUAL.

N.B. CONNECT WELDING CABLES TO OUTPUT STUDS FOR DESIRED POLARITY. POSITION THE WIRE FEEDER VOLTMETER SWITCH TO MATCH THE POLARITY OF THE ELECTRODE CABLE.

N.C. PLACE IDLER SWITCH IN ÒHIGHÓ POSITION.

4-14-2000

S24787-6

F-5

Image 43

Contents Ranger 305D Safety Depends on YouSafety Electric Shock can kill Iii Welding and Cutting Sparks can Cause fire or explosionPrécautions DE Sûreté IvSAFETYOn-Line Product Registration Please Examine Carton and Equipment For Damage ImmediatelyTAbLE of Contents Section F ViiSection D Section ETechnical Specifications Ranger 305D K1727-3 Cold weather starting Safety PrecautionsLocation and Ventilation OIL PRE-OPERATION Engine ServiceTowing Vehicle MountingElectrical Connections Total COMbINED Length Electrode and Work CAbLES CAbLE InstallationWelding Terminals Welding Output CAbLESType Common Electrical Devices Possible Concerns Electrical Device USE with the Ranger 305DSTANDbY Power Connections Auxiliary Power ReceptaclesConnection of Ranger 305D to Premises Wiring Control Cable Model Connection of Lincoln Electric Wire FeedersConnection of LN-15 to the Ranger 305D Across The-Arc ModelConnection of Prince XL Spool GUN to the Ranger 305D Terminals onEngine Operation Safety PrecautionsFor Auxiliary Power General DescriptionWelding Controls Figure b.1 Weld Mode Selector SwitchStart Push bUTTON Wire Feeder Voltmeter SwitchEngine Controls Figure b.2 Glow Plug Push bUTTONTAbLE b.1 Starting the EngineStopping the Engine Welder OperationDownhill Pipe Welding Constant Current CC-STICK WeldingTIG Welding Typical Current Ranges 1 for Tungsten ELECTRODES2ARC Gouging Wire WELDING-CVRanger 305D Extension Cord Length Recommendations Auxiliary PowerT12153-9 50 AMP, 120/240 V Power Plug Field Installed Options / AccessoriesEngine Maintenance Components KUbOTA D722 Diesel Engine Routine MaintenanceKUbOTA D722 Diesel Engine Engine Oil Refill capacities AIR CleanerEngine Oil Change Oil Filter ChangeInsert the New Radial Seal Filter Properly Check Connectors for Tight FitRemove the Filter Inspect the New Filter for DamageTightening the FAN bELT Cooling SystemBLEEDING the Fuel System Arrestor Engine AdjustmentBATTERY Maintenance Servicing Optional SparkGfci Receptacle Testing and RESET- Ting Procedure Welder / Generator MaintenanceHOW to USE TROUbLESHOOTING Guide TROUbLESHOOTINGCause Recommended Course of Action PRObLEMSSymptoms POSSIbLEWelding without a control cable Functioning properly / linkage Faulty control cable. Repair or Your local Lincoln Authorized Field Service FacilityDiagrams Diagrams Diagrams Diagrams S24787-6 Engine Welders /LN-8 Connection DiagramDiagrams Diagrams Diagrams Diagrams Diagrams Dimension Print Ranger 305D Ranger 305D Precaucion Guards off