Campbell Hausfeld HL5500 Series, HS5500 General Safety, Assembly, Oil-Lubricated Compressors

Oil-Lubricated Compressors

General Safety	Never remove or
	attempt to adjust
Information
	safety valve. Keep safety valve free
(Continued)	from paint and other accumulations.		Mounting
2. Follow all local electrical and safety			Tubes
	Never attempt to repair
codes as well as in the US, National
Electrical Code (NEC) and	or modify a tank!
	Welding, drilling or any
Occupational Safety and Health Act
	other modification will
(OSHA).
	weaken the tank resulting in damage		Screws
3. Only persons well acquainted with	from rupture or explosion. Always
	replace worn or damaged tanks.
these rules of safe operation should
	Drain liquid from		Figure 1 - Handle Assembly
be allowed to use the compressor.
	tank daily.
4. Keep visitors away and NEVER allow	12. Tanks rust from moisture build-up,	Assembly
children in the work area.
	which weakens the tank. Make sure
5. Wear safety glasses		HANDLE ASSEMBLY (Figure 1)
	to drain tank daily and inspect
and use hearing	periodically for unsafe conditions	1. Slide handle into mounting tubes
protection when
	such as rust formation and corrosion.		welded to tank. Align holes in tube
operating the pump
	13. Fast moving air will stir up dust and		and handle.
or unit.
	debris which may be harmful.	2. Insert four (4) bolts and tighten.
6. Do not stand on or use the pump or
	Release air slowly when draining		Never use the
unit as a handhold.
	moisture or depressurizing the
			handle to lift the
7. Before each use, inspect compressed
	compressor system.	unit completely off the ground. Only
air system and electrical components	This product or	use the handle to lift one end so the
for signs of damage, deterioration,		wheels may be used to move the unit.
	its power cord
		WHEEL ASSEMBLY (Figure 2)
weakness or leakage. Repair or	contains chemicals known to the State
replace defective items before using.	of California to cause cancer and birth	Wheel assembly kit includes:
8. Check all fasteners at frequent	defects or other reproductive harm.
		-	2 wheels*
	Wash hands after handling.
intervals for proper tightness.
	SPRAYING PRECAUTIONS	-	2 axle bolts*

	Do not spray	-	2 lock washers*
Motors, electrical
	flammable	-	2 washers*
equipment and controls	materials in vicinity of open flame or	-	2 nuts*
can cause electrical arcs	near ignition sources including the
that will ignite a	compressor unit.	The items marked with an asterisk (*)
flammable gas or vapor. Never operate	14. Do not smoke when spraying paint,	were shipped loose with the unit.
or repair the unit near a flammable gas
	insecticides, or other flammable	1. Wheel has an offset hub. With offset
or vapor. Never store flammable liquids
or gases in the vicinity of the	substances.		hub facing axle iron, assemble axle
compressor.	15. Use a face mask/		bolt through holes in wheel and axle
	respirator when		iron.
	spraying and spray in	2. Place flat washer and lock washer on
Compressor parts may	a well ventilated area
			axle bolt. Then tighten nut securely
be hot even if the unit	to prevent health and
			to threaded part of axle bolt.
is stopped.	fire hazards.
9. Keep fingers away from a running	16. Do not direct paint or other sprayed
	material at the compressor. Locate
compressor; fast moving and hot
	compressor as far away from the
parts will cause injury and/or burns.
	spraying area as possible to
10. If the equipment should start to
	minimize overspray accumulation
abnormally vibrate, STOP the
	on the compressor.
engine/motor and check
	17. When spraying or cleaning with
immediately for the cause. Vibration			Hex
	solvents or toxic chemicals, follow
is generally a warning of trouble.			Nut
	the instructions provided by the		Washer
11. To reduce fire hazard,	chemical manufacturer.		Lock washer	Axle bolt
keep engine/motor			Wheel
exterior free of oil,		Figure 2 - Wheel Assembly
solvent, or grease.
www.chpower.com

2