Studer Innotec HPC 2800-12, HPC 4400-24, HPC 6000-48, HPC 8000-48 manual Liability Disclaimer

Page 4

STUDER INNOTEC

HP-COMPACT

1.4Liability Disclaimer

Respecting this manual, servicing and method of installation, functioning, application and maintenance of the appliance can not be controlled or supervised by STUDER INNOTEC. Hence we do not accept any liability and responsibility for damages, losses and costs which result through the use of this appliance or which result through incorrect installation, incorrect operation or wrong application and maintenance, or which by some other means maybe connected to each other.

The use of STUDER INNOTEC’s inverters does exclusively involve the user’s liability.

This device is not designed for applications involving health care and medical treatments where the patient life is concerned and where any mishap may be lethal. Similarly, we do not accept any liability for any violation of the patents rights or violation of any third party’s rights resulting from the use of this appliance STUDER INNOTEC reserves the right to modify the technical data or these operating instructions without any prior notice.

1.5Warning

This manual must be readily available for the user at any time. The user must be familiar with the precautions and safety aspects in the country of installation.

During operation of HP-COMPACT, high voltages are generated at the connections and inside of the appliance which could be lethal. Work on the appliance and on the installation should only be carried out by skilled and trained people.

The whole installation connected with the HP-COMPACT must comply with the rules and codes in force.

People without the written authorization from STUDER INNOTEC are strictly forbidden to carry out any change or repair on the appliances. For authorized changes only original parts are to be used.

The HP-COMPACT may only be used when it has been installed in accordance with these instructions and all parts have been correctly assembled and installed.

The HP-COMPACT may only be connected to lead-acid or lead-gel batteries.

Caution: Even when a HP-COMPACT has been disconnected from all connections, at the OUTPUT point there could still be deadly voltages present. To remove these voltages you must switch on the HP-COMPACT ON with the ON/OFF switch. After one minute the electronics are discharged and any work can now be safely carried out.

The HP-COMPACT is only suitable for internal use and under no circumstances should it be subjected to snow, rain, or any other wet conditions.

By installations in motorized vehicles the HP-COMPACT must be protected from water-spray and any other wet conditions.

Caution: In normal use lead-acid and lead-gel batteries give out explosive gases. Never smoke or allow a spark or flame in the vicinity of batteries. The batteries must always be stored or placed in a well ventilated room, they should be placed in such a way that there is no danger of short-circuit through carelessness. Never charge frozen batteries.

1.6Special precautions

While working on batteries there should always be a second person close to you or within your voice range, in case help is needed.

HP-COMPACT V5.4

6/80

Image 4
Contents Sine wave Inverter, Battery charger, Transfersystem HP-COMPACT HPCHP-COMPACT Quality and Warranty Warranty DisclaimerGeneral Information Operating instructionsSpecial precautions Liability DisclaimerPrinciple schematic IntroductionDescription of the main functions Battery connecting Mounting and installing Installation placeFixing ConnectionsPre-installation settings CablingConnection to battery 3.6.1.1 On the appliance side Connection to Remote control Connection to Temperature Sensor TempConnection to the 230Vac-consumer appliances AC Output Connection to the 230Vac Input AC InputControl Display and control parametersLight Emitting Diodes LED LEDPush buttons Turning KnobsInverter Charge detection system „StandbyBattery Condition Overheating Over TempBattery charger Default values for battery voltage thresholdsCycle of charge Equalization chargingSet the Input Limit Input current repartition Power sharingCharging current Transfer system Fast UPS- Mode for the Transfer Switch Delayed mode of the Transfer SystemMultifunctional Contact Set the transfer voltage thresholdRemote Control RCC-01 HP-COMPACTStandard setting Remote control for „Power Sharing RPS-01Programming Battery voltages and absorption time Reset value default settingsSet the voltage and timing threshold Auxiliary contact Table of voltage and timing thresholdPrinciple Programming of the Auxiliary ContactPower cut of the second priority loads Manual operating of Auxiliary ContactInstallation Maintenance Diagram of the different modesDisabling some of the HP-COMPACT functions Declaration of CE ComplianceTechnical Data