Sterling Plumbing 882 00276.00 specifications Manufacturer Motor Color, Input Number

Page 12

Basic Input Parameters for Digital Dosing Feeder with

Injection Software (P1._ _ - Older units) or (P2._ _ - newer units)

Hold Stop and Input buttons until “7” flashes

-Enter the input number for the specific motor from the table below.

-This value sets the impulses of the encoder.

Manufacturer	Motor Color	RPM	Input Number
Bauer	Blue	6.4	11739
Bauer	Blue	11.5	6600
Bauer	Blue	35.5	2135
Bison	Black	2	65000
Bison	Black	6	25200
Bison	Black	12	14103
Bison	Black	38	4387

Press Input button

-When “8” flashes, enter 0.7 for Blue Bauer motor.

-Or, enter 0.5 for the black Bison or Colorblend S motor.

-This value sets the nominal current for the motor.

Digital Dosing Units

12

Image 12

Contents SDD Series Digital Dosing Additive Feeders Table of Contents Introduction Digital Dosing Units Controller Keypad and LED DisplayKeys and Symbols Symbols Quick Start-up UnpackingMounting Recipe Setup for Injection Molding DD Discs Calibration NumberDT Discs Calibration Number DP DiscsRecipe Setup for Extrusion CalibrationDigital Dosing Units Manufacturer Motor Color Input NumberDigital Dosing Units Digital Dosing Units Digital Dosing Units RPM Digital Dosing Units Digital Dosing Units Digital Dosing Units Initial Installation and Operation Initial InstallationElectrical diagram of connections Electrical DiagramExtruder Follower Interface Signal Converter Diagram of analog inputsSignal Converter with AC Power Supply Signal Converter with DC Power Supply VDC Mini Power SupplyInitial Operation Injection Molding Recipe Input Injection MoldingStep Step Step Operation Injection Molding Extrusion Constant Standard Recipe Input Extrusion ConstantExtrusion Constant, parameter 3 is skipped Step Step Operation Extrusion Constant Extrusion Proportional Extruder Follower Option Recipe Input Extrusion ProportionalStep Step Operation Extrusion Proportional Extruder Follower Option Determining the Calibration Weight CalibrationRepeat steps 3 and 4 four 4 more times Digital Dosing Units Advanced Operations/ Control Functions Recipe Storage and RecallRecipe Storage Recipe Recall Acknowledging Alarms Clearing the TotalizerAlarms Level switches probesCommunication Protocol Interfaces Maintenance Maintenance IntervalsRemoving the Shear plate DD feeder only Removing the shear plateCleaning the DD Digital Dosing Station Installing the shear plateDismantling the Dosing Station Installing the Dosing Station Installing the Dosing Disc Changing the Dosing Disc in the DT Digital Dosing StationRemoving the Dosing Disc Installing Different Types of Dosing Discs Removing / Replacing the Wiper in the DT Dosing StationDD Discs Cleaning the DT Dosing Station Exchangeable Stations DP Discs CalibrationDisc Replacing Fuses See Appendix D for fuse part numbersAppendix a Troubleshooting General Troubleshooting Unit Will Not OperateMalfunctions Error Codes Error Codes Determining the Software Setup Factor Recipe FormulasInjection Molding Recipe Limitations for Injection MoldingExtrusion Recipe Limitations ExtrusionAppendix B Basic Parameter Settings Extrusion ModeMax. input frequency = Hz Example Probe Example Digital Dosing Units Disc Dosing Factor Disc Guide 20 kg/h DT30 204010F Default Calibration # 150 grams/rev Disc Dosing Factor Table One 1 for GranuleProcessing Option Hopper Level Probe VirginStarter Calibration Parameters Set-up of Factory Set Operating Parameters Ext = Span factor sf calculated using sf=1000/rpm@10vdc Page Station 1 Digital Dosing Unit Station 2 Digital Dosing Unit Side View TOP ViewGeneral Wiring Diagram for Bauer Motor Page C150 Controller Injection Appendix D Spare Parts List Replacement Motor Order NumbersDosing Disc/Shear Order Numbers Control System Order Numbers Page Service Department Technical AssistanceParts Department Sales Department