Sterling Plumbing 882 00276.00 specifications Rpm

Page 16

Basic Input Parameters for Colorblend C-150 with

Extrusion Software (E1._ _ - Older units) or (E2._ _ - newer units)

Hold Stop and Input buttons until “7” flashes

-Enter the input number for the specific motor from the table below.

-This value sets the impulses of the encoder.

Manufacturer	Motor Color	RPM	Input Number
Bauer	Blue	6.4	11739
Bauer	Blue	11.5	6600
Bauer	Blue	35.5	2135

Bison	Black	2	65000
Bison	Black	6	25200
Bison	Black	12	14103
Bison	Black	38	4387

Press Input button

-When “8” flashes, enter 0.7 for blue Bauer motor.

-Or, enter 0.5 for the black Bison or Colorblend S motor.

-This value sets the nominal current for the motor.

Digital Dosing Units

16

Image 16

Contents SDD Series Digital Dosing Additive Feeders Table of Contents Introduction Digital Dosing Units Controller Keypad and LED DisplayKeys and Symbols Symbols Unpacking Quick Start-upMounting Recipe Setup for Injection Molding DD Discs Calibration NumberDT Discs Calibration Number DP DiscsRecipe Setup for Extrusion CalibrationDigital Dosing Units Manufacturer Motor Color Input NumberDigital Dosing Units Digital Dosing Units Digital Dosing Units RPM Digital Dosing Units Digital Dosing Units Digital Dosing Units Initial Installation and Operation Initial InstallationElectrical diagram of connections Electrical DiagramDiagram of analog inputs Extruder Follower Interface Signal ConverterSignal Converter with AC Power Supply VDC Mini Power Supply Signal Converter with DC Power SupplyInitial Operation Injection Molding Recipe Input Injection MoldingStep Step Step Operation Injection Molding Extrusion Constant Standard Recipe Input Extrusion ConstantExtrusion Constant, parameter 3 is skipped Step Step Operation Extrusion Constant Extrusion Proportional Extruder Follower Option Recipe Input Extrusion ProportionalStep Step Operation Extrusion Proportional Extruder Follower Option Determining the Calibration Weight CalibrationRepeat steps 3 and 4 four 4 more times Digital Dosing Units Recipe Storage and Recall Advanced Operations/ Control FunctionsRecipe Storage Recipe Recall Acknowledging Alarms Clearing the TotalizerAlarms Level switches probesCommunication Protocol Interfaces Maintenance Maintenance IntervalsRemoving the Shear plate DD feeder only Removing the shear plateInstalling the shear plate Cleaning the DD Digital Dosing StationDismantling the Dosing Station Installing the Dosing Station Changing the Dosing Disc in the DT Digital Dosing Station Installing the Dosing DiscRemoving the Dosing Disc Removing / Replacing the Wiper in the DT Dosing Station Installing Different Types of Dosing DiscsDD Discs Cleaning the DT Dosing Station DP Discs Calibration Exchangeable StationsDisc Replacing Fuses See Appendix D for fuse part numbersGeneral Troubleshooting Unit Will Not Operate Appendix a TroubleshootingMalfunctions Error Codes Error Codes Determining the Software Setup Factor Recipe FormulasInjection Molding Recipe Limitations for Injection MoldingExtrusion Recipe Limitations ExtrusionExtrusion Mode Appendix B Basic Parameter SettingsMax. input frequency = Hz Example Probe Example Digital Dosing Units Disc Dosing Factor Disc Guide 20 kg/h DT30 204010F Default Calibration # 150 grams/rev Disc Dosing Factor Table One 1 for GranuleProcessing Option Hopper Level Probe VirginStarter Calibration Parameters Set-up of Factory Set Operating Parameters Ext = Span factor sf calculated using sf=1000/rpm@10vdc Page Station 1 Digital Dosing Unit Station 2 Digital Dosing Unit Side View TOP ViewGeneral Wiring Diagram for Bauer Motor Page C150 Controller Injection Replacement Motor Order Numbers Appendix D Spare Parts ListDosing Disc/Shear Order Numbers Control System Order Numbers Page Service Department Technical AssistanceParts Department Sales Department