Sterling Plumbing 882 00276.00 specifications Quick Start-up, Unpacking, Mounting

Page 8

Section 2: Quick Start-up

Quick Start is intended to help you in starting up your Digital Dosing feeder quickly and easily. Please refer to the manual to go into greater detail.

Unpacking:

1.Unpack box, making sure all parts indicated on packing list are included.

2.Check all parts and equipment for any damage sustained during shipment.

3.If any damage is noted, contact manufacturer for replacement or service.

4.Make sure the following are present before proceeding:

;Power source 110 or 220 volt, single phase, 50 or 60 hertz (verify voltage on Serial Number tag

;Proper mounting flange adapter for the feed throat

;Dry (ZERO VOLTAGE) contact that closes during screw recovery of IMM

;Gram scale to measure weight of additive material for calibration.

Mounting:

1.Mount the complete unit, including dosing hopper full of material, on the feed throat (may need an adapter for feed throat).

2.Identify the motor drive connector (“Amp” connector-black) and connect to motor.

3.Identify the communication cable (DB-9 plug-silver) and connect to DB-9 connector under motor drive assembly.

4.Identify power cord and plug into appropriate outlet.

5.INJECTION MOLDING: Identify the cycle/run cable (2-conductor cable-gray) for connection to a dry (ZERO VOLTAGE) contact that closes during the screw recovery cycle of the molding machine.

6.EXTRUSION: Identify the input cable (2-conductor cable-gray) for connection to 0-10 VDC or 0-20 mA signal that indicates speed (rpm) of the extruder.

Digital Dosing Units

8

Image 8

Contents SDD Series Digital Dosing Additive Feeders Table of Contents Introduction Digital Dosing Units Controller Keypad and LED DisplayKeys and Symbols Symbols Mounting Quick Start-upUnpacking Recipe Setup for Injection Molding DD Discs Calibration NumberDT Discs Calibration Number DP DiscsRecipe Setup for Extrusion CalibrationDigital Dosing Units Manufacturer Motor Color Input NumberDigital Dosing Units Digital Dosing Units Digital Dosing Units RPM Digital Dosing Units Digital Dosing Units Digital Dosing Units Initial Installation and Operation Initial InstallationElectrical diagram of connections Electrical DiagramSignal Converter with AC Power Supply Extruder Follower Interface Signal ConverterDiagram of analog inputs Initial Operation Signal Converter with DC Power SupplyVDC Mini Power Supply Injection Molding Recipe Input Injection MoldingStep Step Step Operation Injection Molding Extrusion Constant Standard Recipe Input Extrusion ConstantExtrusion Constant, parameter 3 is skipped Step Step Operation Extrusion Constant Extrusion Proportional Extruder Follower Option Recipe Input Extrusion ProportionalStep Step Operation Extrusion Proportional Extruder Follower Option Determining the Calibration Weight CalibrationRepeat steps 3 and 4 four 4 more times Digital Dosing Units Recipe Storage Advanced Operations/ Control FunctionsRecipe Storage and Recall Recipe Recall Acknowledging Alarms Clearing the TotalizerAlarms Level switches probesCommunication Protocol Interfaces Maintenance Maintenance IntervalsRemoving the Shear plate DD feeder only Removing the shear plateDismantling the Dosing Station Cleaning the DD Digital Dosing StationInstalling the shear plate Installing the Dosing Station Removing the Dosing Disc Installing the Dosing DiscChanging the Dosing Disc in the DT Digital Dosing Station DD Discs Installing Different Types of Dosing DiscsRemoving / Replacing the Wiper in the DT Dosing Station Cleaning the DT Dosing Station Disc Exchangeable StationsDP Discs Calibration Replacing Fuses See Appendix D for fuse part numbersMalfunctions Error Codes Appendix a TroubleshootingGeneral Troubleshooting Unit Will Not Operate Error Codes Determining the Software Setup Factor Recipe FormulasInjection Molding Recipe Limitations for Injection MoldingExtrusion Recipe Limitations ExtrusionMax. input frequency = Hz Appendix B Basic Parameter SettingsExtrusion Mode Example Probe Example Digital Dosing Units Disc Dosing Factor Disc Guide 20 kg/h DT30 204010F Default Calibration # 150 grams/rev Disc Dosing Factor Table One 1 for GranuleProcessing Option Hopper Level Probe VirginStarter Calibration Parameters Set-up of Factory Set Operating Parameters Ext = Span factor sf calculated using sf=1000/rpm@10vdc Page Station 1 Digital Dosing Unit Station 2 Digital Dosing Unit Side View TOP ViewGeneral Wiring Diagram for Bauer Motor Page C150 Controller Injection Dosing Disc/Shear Order Numbers Appendix D Spare Parts ListReplacement Motor Order Numbers Control System Order Numbers Page Service Department Technical AssistanceParts Department Sales Department