Graco 334135B important safety instructions Quantity Part Description 24W415 24W416 24W417

Page 17

Recommended Parts

				Quantity
Ref	Part	Description
Ref	Part	Description	24W415	24W416	24W417

1001	95/0223/00	O-RING	2	4	1

1002	120901	O-RING	4	4
1003	120902	SCREW, M5x40mm	2	2
1004	120904	SCREW, M5x18mm	6	6	3

1005	120905	NUT, hex, lock M5	2	2
1006	120906	NUT, hex, lock M8 x 1.25	2	2
1007	120907	WASHER, plain #10	4	2
1008	120908	WASHER, plain M8	4	4
1009	120909	BREATHER	2	2
1010	120911	CLAMP, gap-free pinch hose	2	2
1011	120913	SCREW	2	2
1014	255280	VALVE, ball		2
1015	121013	SCREW, M5x25mm		6
1018	---	RING, lock	2	2
1019	---	FITTING, flange	2	2
1020	15K840	O-RING	2	2
1023	---	TANK, 8 liter	1	1
1024	15M226	BALLAST		1
	15K842	BALLAST	1
1025	120915	CAP PLUG, square	2	2
1026*	15M237	FLANGE, 1-1/2 in. NPT			1

*Not Shown

334135B

17

Image 17

Contents PR70e Important Safety InstructionsContents Related Manuals ModelsElectric Shock Hazard Fire and Explosion Hazard IG Machine Key Component IdentificationMachine AB System Shut-Down Key Local Control Module LCMRun Screen Screen Overview and Appendix C LCM SetupLCM Screen Navigation Component Identification 334135B Dispense Valve Recommended PartsStandard Dispense Valves, 255179 Gun Mounted MD2 Valves, LC0120 and LC0122Part Description Quantity Lever Actuated MD2 Valves, LC0121 and LC0123Mixers 1301 1302 1303 Mixer Reference Number and DescriptionShroud Package DescriptionPart Description Mounting, valve, HMI Mounting, HMI Applicator MountingAir Filter and Ball Valve, 24R707 High Temperature Grease FootswitchTanks Quantity Part Description 24W415 24W416 24W417 Unheated, Non-Recirculating Hose Hose PackagesRecommended Parts 334135B Nylon Piston, Stainless Steel Metering Tube Assemblies Piston PackageUhmw Uhmw Piston, Stainless Steel Metering Tube AssembliesShot Size cc Air Motor In. Air Motor Pump Tube Combination InformationMachine Installation InstallationGrounding General Grounding GuidelinesInstall the Dispense Valve and Support Arm, if needed Install the Chemical HosesElectrical Requirements Ground SystemPiston Position Calibration SetupNavigate to the Shot Mode Screen or Operator Mode Screen Perform Pressure Relief Procedure onEngaged Piston Position Manually Move the Piston Drive BlockPrime Dispense Head Prime the Dispense HeadAdjust Dispense Quantity Phasing AdjustmentPrepare the Machine Navigate to the Phasing Shot Calibration ScreenAdjust Phasing Adjust Dispense Valve Snuff Back Operator Mode Screen Adjust Open Dispense Valve ODV TimingNavigate to the Maintenance Mode Run Screen Pressure Relief ProcedureOperation StartupShutdown Relieve pressure. See Pressure Relief Procedure,Clean the Pump Shafts MaintenanceDisassemble and Clean the Dispense Head ScheduleRemove Access Panel Install Upgrade TokenProblem Cause Solution TroubleshootingProblem Cause Solution Trigger LCM Error CodesCode Name Type Causes Fixes Condition Entries in Position CalibraRepair HydraCheck Kit Installation, 24W336Prepare Machine for Kit Installation Adjust Shock Resistance Install Adjustment Screw/CapAdjust the Adjustment Screw/Cap Disassemble the Air Cylinder Air Cylinder Rebuild InstructionsRe-Assemble the Air Cylinder Clean and Inspect the PartsRear Pump Rebuild Instructions Prepare for Operation Assemble the Rear Pump AssemblyDisassemble Cylinder Piston/Cylinder Replacement Kit InstallationInstall Cylinder Check Valve Rebuild Kit Installation Fixed Ratio Base Parts24V935, Pump 24V936, Pump Part Description Assembly Pump Sub-Assembly, 24S053 Collar Check Valve, Assembly LC0093206 201 204 205 202 203 Fixed Ratio Drive Block Assembly, LC010724V933, Motor 24V934, Motor Part Description Air Air Cylinder, 24V933Fixed Ratio Frame Sub-Assembly, LC0290 Ring, support Carbide Package Pump Piston Washer Screw Ball Uhmw Piston, Ceramic Metering Tube AssembliesElectrical Schematics SchematicsElectrical Schematic DB25 Pin Number Pin Function Description Pneumatic SchematicDB25 Pin Function Schematics 334135B Appendix a LCM Icon Overview Position Adjust Phasing Shot AdjustAdjust Amount AdjustDisable Mode Screen Splash Screen Operator Mode ScreenShot Mode Screen Mode Selection Programming ScreenShot Amount or Stroke % Adjust Screen Maintenance Mode Run ScreenError Code Acknowledgement Screen Run Screen while DispensingPhasing Shot Calibration Screen Appendix C LCM Setup Screen OverviewSetup Screen Password Set/Clear Screen Kits Nylon and Uhmw Piston Replacement KitsLCF Piston Size mm2 LCE Piston Size mm2MD2 Valve Recommended Spare PartsDimensions Dimensions Technical Data Graco Information Graco Standard Warranty