Graco 334135B Fixed Ratio Drive Block Assembly, LC0107, 206 201 204 205 202 203

Page 52

Parts

Fixed Ratio Drive Block Assembly, LC0107

206

201 3

204

205

202

205

203 2

1	Apply grease (part 115982) to all internal parts.
2	Tighten retaining nut until alignment rod (202) cannot be moved. Loosen
	retaining nut until alignment rod can move side-to-side with no in-and-out
	movement.
3	Torque to 64 in-lb (7.2 N•m).

FIG. 18

Ref	Part	Description	Quantity

201	120891	SCREW, set, socket, cone point	2
202	15K801	ROD, alignment	2
203	15K802	RETAINER, nut	2
204	15K805	BLOCK, drive	1
205	15K868	WASHER, female, male modified, assembly	2
206 ▲	84_0130-27_11	LABEL, warning, pinch point	1

▲Replacement Danger and Warning labels, tags, and cards are available at no cost.

52

334135B

Image 52

Contents Important Safety Instructions PR70eContents Models Related ManualsElectric Shock Hazard Fire and Explosion Hazard Machine Component IdentificationIG Machine Key Local Control Module LCM AB System Shut-Down KeyLCM Screen Navigation Screen Overview and Appendix C LCM SetupRun Screen Component Identification 334135B Recommended Parts Dispense ValveStandard Dispense Valves, 255179 Gun Mounted MD2 Valves, LC0120 and LC0122Lever Actuated MD2 Valves, LC0121 and LC0123 Part Description QuantityMixers Reference Number and Description 1301 1302 1303 MixerShroud Package DescriptionApplicator Mounting Part Description Mounting, valve, HMI Mounting, HMIHigh Temperature Grease Footswitch Air Filter and Ball Valve, 24R707Tanks Quantity Part Description 24W415 24W416 24W417 Hose Packages Unheated, Non-Recirculating HoseRecommended Parts 334135B Piston Package Nylon Piston, Stainless Steel Metering Tube AssembliesUhmw Piston, Stainless Steel Metering Tube Assemblies UhmwPump Tube Combination Information Shot Size cc Air Motor In. Air MotorInstallation Machine InstallationGrounding General Grounding GuidelinesInstall the Chemical Hoses Install the Dispense Valve and Support Arm, if neededGround System Electrical RequirementsSetup Piston Position CalibrationPerform Pressure Relief Procedure on Navigate to the Shot Mode Screen or Operator Mode ScreenEngaged Piston Position Manually Move the Piston Drive BlockPrime the Dispense Head Prime Dispense HeadPhasing Adjustment Adjust Dispense QuantityPrepare the Machine Navigate to the Phasing Shot Calibration ScreenAdjust Phasing Adjust Dispense Valve Snuff Back Adjust Open Dispense Valve ODV Timing Operator Mode ScreenPressure Relief Procedure Navigate to the Maintenance Mode Run ScreenOperation StartupRelieve pressure. See Pressure Relief Procedure, ShutdownMaintenance Clean the Pump ShaftsDisassemble and Clean the Dispense Head ScheduleInstall Upgrade Token Remove Access PanelTroubleshooting Problem Cause SolutionProblem Cause Solution LCM Error Codes TriggerCode Name Type Causes Fixes Condition Entries in Position CalibraPrepare Machine for Kit Installation HydraCheck Kit Installation, 24W336Repair Adjust the Adjustment Screw/Cap Install Adjustment Screw/CapAdjust Shock Resistance Air Cylinder Rebuild Instructions Disassemble the Air CylinderClean and Inspect the Parts Re-Assemble the Air CylinderRear Pump Rebuild Instructions Assemble the Rear Pump Assembly Prepare for OperationInstall Cylinder Piston/Cylinder Replacement Kit InstallationDisassemble Cylinder Check Valve Rebuild Kit Installation Parts Fixed Ratio Base24V935, Pump 24V936, Pump Part Description Assembly Pump Sub-Assembly, 24S053 Check Valve, Assembly LC0093 CollarFixed Ratio Drive Block Assembly, LC0107 206 201 204 205 202 203Air Cylinder, 24V933 24V933, Motor 24V934, Motor Part Description AirFixed Ratio Frame Sub-Assembly, LC0290 Uhmw Piston, Ceramic Metering Tube Assemblies Ring, support Carbide Package Pump Piston Washer Screw BallSchematics Electrical SchematicsElectrical Schematic DB25 Pin Function Pneumatic SchematicDB25 Pin Number Pin Function Description Schematics 334135B Appendix a LCM Icon Overview Phasing Shot Adjust Position AdjustAdjust Amount AdjustSplash Screen Operator Mode Screen Disable Mode ScreenShot Mode Screen Mode Selection Programming ScreenMaintenance Mode Run Screen Shot Amount or Stroke % Adjust ScreenError Code Acknowledgement Screen Run Screen while DispensingSetup Screen Password Set/Clear Screen Appendix C LCM Setup Screen OverviewPhasing Shot Calibration Screen Nylon and Uhmw Piston Replacement Kits KitsLCF Piston Size mm2 LCE Piston Size mm2Recommended Spare Parts MD2 ValveDimensions Dimensions Technical Data Graco Standard Warranty Graco Information