Panasonic EY7541 IV. Assembly, Attaching or Removing Socket, Attaching or Removing Bat­ tery Pack

Page 6

not attempt to charge any other cordless tool or battery pack with this charger.

13)Do not attempt to charge the battery pack with any other charger.

14)Do not attempt to disassemble the battery pack housing.

15)Do not store the tool and battery pack in locations where the temperature may reach or exceed 50°C (122°F) (such as a metal tool shed, or a car in the summer), which can lead to deterioration of the storage battery.

16)Do not charge battery pack when the temperature is BELOW 0°C (32°F) or ABOVE 40°C (104°F). This is very important in order to maintain optimal condition of the battery pack.

17)Do not incinerate the battery pack. It can explode in a fire.

18)Avoid dangerous environment. Do not use charger in damp or wet locations.

19)The charger is designed to operate on standard household electrical power only. Do not attempt to use it on any other voltage!

20)Do not abuse cord. Never carry charger by cord or yank it to disconnect from outlet. Keep cord away from heat, oil and sharp edges.

21)Charge the battery pack in a well ventilated place, do not cover the charger and battery pack with a cloth, etc., while charging.

22)Use of an attachment not recommended may result in a risk of fire, electric shock, or personal injury.

23)Do not short the battery pack. A battery short can cause a large current flow, over heating and create the risk of fire or personal injury.

24)NOTE: If the supply cord of this appliance is damaged, it must only be replaced by a repair shop authorized by the manufacturer, because special purpose tools are required.

25)TO REDUCE THE RISK OF ELECTRIC SHOCK, THIS APPLIANCE HAS A POLARIZED PLUG (ONE BLADE IS WIDER THAN THE OTHER).

This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.

IV. ASSEMBLY

NOTE:

When attaching or removing a bit or socket, disconnect battery pack from tool or place the trigger switch in the center position (switch lock).

Attaching or Removing Socket

1.Attaching Socket

Attach the socket by sliding the female detent on the bottom of the socket to the square drive on the body.

Make sure the socket is firmly connected to the body.

2.Removing Socket Pull out the socket.

NOTE:

Attaching or Removing Original Options and Sockets

Keep the body above freezing point (0°C 32°F) when attach or detach original options and sockets to the square drive on the body. The cushion rubber in the square drive to push up the ball may get hard under freezing point. This requires extra force in detaching and attaching sockets.

Attaching or Removing Bat­ tery Pack

1.To connect the battery pack:

Line up the alignment marks and attach the battery pack.

Slide the battery pack until it locks into position.

Alignment marks

- -

Image 6
Contents Model No EY7541 ImportanteBattery low warning lamp Index/Index/IndiceElectrical Safety General Safety RulesWork Area Safety Personal SafetyII. Specific Safety Rules Battery Tool Use and CareService Battery Pack Important Safety InstructionsSymbol Meaning IV. Assembly Attaching or Removing SocketAttaching or Removing Bat­ tery Pack Operation Control Panel Impact Power Mode SelectTo Change the Belt Hook Location Side Recommended work guideline tableBattery Pack Life Battery Pack For Appropriate Use of Bat­ tery PackLi­ion Battery Pack EY9L40 Battery RecyclingLi-ion Battery Pack Battery Charger ChargingCommon Cautions for the Li- ion/Ni-MH/Ni-Cd Battery Pack Ni-MH/Ni-Cd Battery PackVI. Maintenance VII. Tightening TorqueFactors Affecting Tighten­ ing Torque Bolt Tightening ConditionsVIII. Accessories Li-ion battery pack Ni-Cd/Ni-MH battery packSécurité électrique Rite GeneralesSécurité de la zone de travail Sécurité personnelleUtilisation et soins de l’outil méca­ nique Utilisation et soins de la batterie de l’outilMaintenez les outils de coupe affûtés et propres Réparation Symbole SignificationParticulieres AvertissementIII.CHARGEURDEBAT­ Instructions de sécurité impor­ tantesFixation ou retrait de la bat­ terie autonome IV. MontageFixation ou retrait de la douille RemarqueUtilisation du commutateur pour une rotation en sens normal Corps principalComment utiliser le crochet de ceinture Mise EN GardePanneau de commande Tableau de référence des travaux recommandésSélection du mode de puissance de per­ cussion Batterie Batterie autonome Li-ion EY9L40Longévité des batteries autonomes Chargeur de batterie RechargeBatterie autonome Li­ion Recyclage de la batterie autonomeBatterie autonome Ni-MH/Ni-Cd VI. Entretien VII.COUPLE DE SerrageFacteurs affectant le couple de serrage Conditions de serrage des boulons Conditions de serrage Les boulons suivants sont utilisésCaracteristiques Techniques VIII.ACCESSOIRESIX. Appendice Batterie autonome Li-ionBatterie autonome Ni-MH/Ni-Cd Seguridad eléctrica DAD GeneralesSeguridad del lugar de trabajo Seguridad personalUso y cuidados de herramientas eléctricas Uso y cuidado de la herramienta a bateríaMantenga las herramientas de corte afiladas y limpias ¡ADVERTENCIA DAD EspecíficasServicio Símbolo SignificadoIII. Para EL CARGA­ DOR DE Bateria Y LA Bateria Instrucciones de seguridad im­ portantesColocación y extracción de la batería IV. MontajeInstalación o desmontaje del cubo NotaCómo utilizar el gancho del cinturón FuncionamientoCuerpo principal PrecauciónCuadro de guías de trabajo recomen­ dadas Para cambiar el lugar de ubicación del gancho de cinturónPanel de controle Selección de modo de potencia de impactoLuz de advertencia de batería baja Bloque de pilas Para un uso adecuado de la bateríaBatería de Li-ión EY9L40 Luz LEDReciclado de la batería Cargador de la batería CargaVida útil de la batería Precauciones comunes para las baterías Li­ión/Ni­MH/Ni­CdBatería Ni-MH/Ni-Cd VI. Mantenimiento VII.PAR DE AprieteFactores que afectan al par de apriete Condiciones de apriete de pernos Condiciones de apriete Se utilizan los siguientes pernosVIII.ACCESORIOS IX. AnexoEspecificaciones Batería de Li-ión Batería Ni-MH/Ni-CdMemo Panasonic Consumer Electronics Company
Related manuals
Manual 4 pages 18.02 Kb

EY7541 specifications

The Panasonic EY7541 is a versatile and powerful cordless impact wrench designed for professionals and enthusiasts seeking reliability and performance in their tools. With a robust build and advanced technology, this tool stands out in the competitive landscape of power tools, particularly for automotive, construction, and industrial applications.

One of the standout features of the EY7541 is its impressive 18V lithium-ion battery system, which offers extended runtime and quick charging capabilities. This ensures that users can work longer without frequent interruptions, making it ideal for heavy-duty tasks. The tool is equipped with a compact design, lending it the maneuverability required for tight spaces, while still providing substantial torque and power.

The EY7541 boasts a powerful motor that delivers high torque output, making it suitable for driving large bolts and fasteners efficiently. Its dual speed settings allow users to adjust the wrench's performance based on their specific job requirements. The first speed is ideal for precision work or driving smaller screws, while the second speed maximizes the power for tougher applications, ensuring versatility across various tasks.

Another key characteristic of the Panasonic EY7541 is its ergonomic design. The tool features a comfortable grip that reduces fatigue during extended use, allowing for improved productivity and ease of operation. The weight distribution of the tool also enhances stability, which is crucial for maintaining control during high-speed applications.

Durability is a hallmark of the Panasonic brand, and the EY7541 is no exception. Built with high-quality materials, this impact wrench is designed to withstand the rigors of demanding work environments. The robust housing protects the internal components from damage, and the tool's design includes protective features to prevent overheating.

Moreover, the EY7541 incorporates advanced safety technologies, including an overload protection system that helps prevent damage to the motor, ensuring longevity and consistent performance. The inclusion of LED lights enhances visibility in low-light conditions, allowing users to work effectively even in challenging environments.

In conclusion, the Panasonic EY7541 impact wrench is a reliable tool that integrates power, efficiency, and user-centric features. With its advanced battery technology, variable speed settings, ergonomic design, and durability, it is a top choice for professionals in need of a high-performing impact wrench that can handle a variety of tasks with ease.