Porter-Cable 33-891, 33-892, 33-890, 33-895X Compound Miter Cutting, Out-Ripping, In-Ripping

Page 26

COMPOUND MITER CUTTING

Compound miter cutting is performed in the same manner as miter cutting except the saw blade is also tilted to cut a bevel. The settings and operation are similar to miter cutting except that the blade is first tilted to the desired angle on the bevel scale before it is clamped in place. Fig. 64, shows a compound miter cutting operation on the radial saw.

RIPPING

Ripping involves making a lengthwise cut through a board along the grain. When ripping, the track arm (B) Fig. 65 and 66, are clamped at “0” on the miter scale. The yoke is then positioned and clamped so that the blade is parallel to the fence in either the inboard or outboard position.When feeding the material, one edge rides against the fence while the flat side of the board rests on the table. The guard should be lowered on the infeed side until it almost touches the workpiece, as shown in Figs. 65 and 66, to act as a holddown. The splitter and anti-kickback fingers (A) Fig. 65, should be adjusted accordingly. The operator’s hands should always be well away from and to the side of the blade. When ripping narrow work, always use a push stick as shown in Fig. 66, to push the work between the fence and blade. NOTE: The workpiece must have one straight edge to follow the fence. If board is bowed, place hollow side down.

THE CUTTINGHEAD CLAMP KNOB (C) FIGS. 65 AND 66, SHOULD BE SECURELY TIGHTENED FOR ALL RIPPING OPERATIONS. PAY PARTICULAR ATTENTION TO WARNING LABEL WHICH STATES THAT MATERIAL MUST NEVER BE FED INTO THE OUTFEED END OF THE BLADE GUARD.

OUT-RIPPING

Out-ripping involves all of the general conditions stated under RIPPING. The yoke is clamped at right angle to the track arm with the blade guard facing the front of the machine. The cuttinghead is positioned on the out-rip scale to the desired setting and clamped in position. The workpiece is fed from the left side of the saw. Fig. 65, shows a typical out-ripping operation on the radial saw.

IN-RIPPING

In-ripping involves all of the general conditions stated under RIPPING. The yoke is clamped at right angle to the track arm with the blade guard facing the rear of the machine. The cuttinghead is positioned on the in-rip scale to the desired setting and clamped in position. The workpiece is fed from the right side of the saw. Fig. 66, shows a typical in-ripping operation on the radial saw. Note the push stick is being used due to the narrow workpiece.

WHEN RIPPING WORK LESS THAN FOUR INCHES WIDE, A PUSH STICK SHOULD BE USED TO COMPLETE THE FEED

B

A

Fig. 63

Fig. 64

C

B

A

Fig. 65

BC

Fig. 66

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Radial Arm Saw Table of Contents Important Safety InstructionsSafety Guidelines Definitions California PropositionGeneral Safety Rules Additional Safety Rules for Radial ARM Saws Avoid Kickback byThree Phase Operation Power ConnectionsMotor Specifications Grounding InstructionsExtension Cords Minimum Gauge Extension CordCarton Contents Functional DescriptionDisconnect Machine from Power Source AssemblyAssembly Tools Required Guide to PartsAssembling Cuttinghead to Track ARM Assembling Legs to BaseAssembling Overarm Elevating Handle AB CPage Assembling Starter BOX to Base 33-891 and 33-892 Models Adjusting Table Brackets Parallel to Track ARM Page Assembling Table Clamps and Table Clamp Rods Assembling Table Boards Assembling SAW Blade and Blade GuardStarting and Stopping SAW Locking Switch in OFF PositionOperation Adjusting Overarm Column Adjusting Yoke Clamp HandleAdjusting Cuttinghead Ball Bearings Against Track Rods Adjusting Track RodsAdjusting Blade Square with Table TOP Adjusting Track ARM Clamp Handle Adjusting SAW Travel Square with Fence Removing Heeling in SAW CUT CROSS-CUT StopAssembling Accessory Moulding Cutterhead Guard Adjusting Blade Guard and ANTI-KICKBACK RODAdjusting Track ARM Stop CROSS-CUTTING Miter CuttingOUT-RIPPING Compound Miter CuttingRipping IN-RIPPINGPushstick Constructing a Push StickTroubleshooting Guide Maintenance Disconnect Machine from the Power SourceWarranty ServiceAccessories Page Page Canadian PORTER-CABLE Delta Service Centers
Top Page Image Contents