Porter-Cable 33-890, 33-892, 33-891, 33-895X instruction manual Cross-Cutting, Miter Cutting

Page 25

4.When using the moulding cutterhead, the motor should be positioned as shown in Fig. 61. The height of the guard (A) Fig. 61, can be adjusted by loosening three screws (C).

C

C

Fig. 61

MACHINE USE

CROSS-CUTTING

The first operation which should be learned on the radial saw is cross-cutting. Cross-cutting consists of supporting the workpiece against the fence and pulling the saw blade through the material at right angles to it.

When cross-cutting, the track arm (A) should be indexed at “0” and the track arm clamp handle (B) Fig. 62, tightened. The fence should be clamped between the table boards. The saw blade is to be to the left and behind the fence. The workpiece is placed on the table and butted against the fence. The saw blade should be clear of the fence and table when the machine is turned on. Then the saw blade is lowered until it lightly cuts into the table surface. The operator should position himself a little to the left of the machine for better visibility while cutting. Pull the saw blade across the work, just far enough to cut it off, and return the saw blade to its starting position. Wait for the blade to stop before touching the cut off piece.

The operator must always be conscious of where his hands are; that they are clear of the blade and holding the workpiece firmly. As an added measure of operator safety, since the splitter and anti-kickback fingers are not used in the cross-cutting operation, the anti-kickback rod (C) can be turned upside down and locked in place so the rod just clears the workpiece. In this position the rod can act as a guard from the exposed teeth of the blade. Fig. 62 shows a cross-cutting operation on a radial saw. The operator should always be sure to return the cutterhead carriage to the full rear position after each cross-cut operation.

When cross-cutting material more than 1” thick, the fence must be positioned immediately behind the fixed front table board.

B

A

C

Fig. 62

MITER CUTTING

Miter cutting is similar to cross-cutting except the workpiece is cut off at an angle (up to 45° right or left) rather than being cut off square. The settings and operation are performed in the same manner as cross- cutting except that the track arm (A) Fig. 63, is first positioned to the desired angle on the miter scale before it is clamped in place with clamp handle (B). The operator should position the hand holding the workpiece on the opposite side to the direction of the miter so the blade is pulled through the workpiece and away from the hand. Fig. 63, shows a typical miter cutting operation on the radial saw.

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Radial Arm Saw Important Safety Instructions Table of ContentsCalifornia Proposition Safety Guidelines DefinitionsGeneral Safety Rules Avoid Kickback by Additional Safety Rules for Radial ARM SawsMotor Specifications Power ConnectionsThree Phase Operation Grounding InstructionsMinimum Gauge Extension Cord Extension CordsFunctional Description Carton ContentsAssembly Tools Required AssemblyDisconnect Machine from Power Source Guide to PartsAssembling Overarm Elevating Handle Assembling Legs to BaseAssembling Cuttinghead to Track ARM AB CPage Assembling Starter BOX to Base 33-891 and 33-892 Models Adjusting Table Brackets Parallel to Track ARM Page Assembling Table Clamps and Table Clamp Rods Assembling SAW Blade and Blade Guard Assembling Table BoardsOperation Locking Switch in OFF PositionStarting and Stopping SAW Adjusting Yoke Clamp Handle Adjusting Overarm ColumnAdjusting Track Rods Adjusting Cuttinghead Ball Bearings Against Track RodsAdjusting Blade Square with Table TOP Adjusting Track ARM Clamp Handle Adjusting SAW Travel Square with Fence CROSS-CUT Stop Removing Heeling in SAW CUTAdjusting Track ARM Stop Adjusting Blade Guard and ANTI-KICKBACK RODAssembling Accessory Moulding Cutterhead Guard Miter Cutting CROSS-CUTTINGRipping Compound Miter CuttingOUT-RIPPING IN-RIPPINGConstructing a Push Stick PushstickDisconnect Machine from the Power Source Troubleshooting Guide MaintenanceAccessories ServiceWarranty Page Page Canadian PORTER-CABLE Delta Service Centers
Top Page Image Contents