Quantaray N52FN, N62FN Safety Instructions, AIR Supply and Connections, Loading Tool, Operation

Page 3

SAFETY INSTRUCTIONS

EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn by the operator and others in the work area when connecting to air supply, loading, operating or servicing this tool. Eye protection is required to guard against flying fasteners and debris, which could cause severe eye injury.

The employer and/or user must ensure that proper eye protection is worn. Eye protection equipment must conform to the requirements of the American National Standards Institute, ANSI Z87.1 and provide both frontal and side protection. NOTE: Non-side shielded spectacles and face shields alone do not provide adequate protection.

CAUTION: Additional Safety Protection will be required in some environments. For example, the working area may include exposure to noise level which can lead to hearing damage. The employer and user must ensure that any necessary hearing protection is provided and used by the operator and others in the work area. Some environments will require the use of head protection equipment. When required, the employer and user must ensure that head protection conforming to ANSI Z89.1 is used.

AIR SUPPLY AND CONNECTIONS

Do not use oxygen, combustible gases, or bottled gases as a power source for this tool as tool may explode, possibly causing injury.

Do not use supply sources which can potentially exceed 200 P.S.I.G. as tool may burst, possibly causing injury.

The connector on the tool must not hold pressure when air supply is disconnected. If a wrong fitting is used, the tool can remain charged with air after disconnecting and thus will be able to drive a fastener even after the air line is disconnected possibly causing injury.

Do not pull trigger or depress contact arm while connected to the air supply as the tool may cycle, possibly causing injury.

Always disconnect air supply: 1.) Before making adjustments; 2.) When servicing the tool; 3.) When clearing a jam; 4.) When tool is not in use; 5.) When moving to a different work area, as accidental actuation may occur, possibly causing injury.

LOADING TOOL

When loading tool: 1.) Never place a hand or any part of body in fastener discharge area of tool; 2.) Never point tool at anyone; 3.) Do not pull the trigger or depress the trip as accidental actuation may occur, possibly causing injury.

OPERATION

Always handle the tool with care: 1.) Never engage in horseplay; 2.) Never pull the trigger unless nose is directed toward the work; 3.) Keep others a safe distance from the tool while tool is in operation as accidental actuation may occur, possibly causing injury.

The operator must not hold the trigger pulled on contact arm tools except during fastening operation as serious injury could result if the trip accidentally contacted someone or something, causing the tool to cycle.

Keep hands and body away from the discharge area of the tool. A contact arm tool may bounce from the recoil of driving a fastener and an unwanted second fastener may be driven possibly causing injury.

Check operation of the contact arm mechanism frequently. Do not use the tool if the arm is not working correctly as accidental driving of a fastener may result. Do not interfere with the proper operation of the contact arm mechanism.

Do not drive fasteners on top of other fasteners or with the tool at an overly steep angle as this may cause deflection of fasteners which could cause injury.

Do not drive fasteners close to the edge of the work piece as the wood may split, allowing the fastener to be deflected possibly causing injury.

This nailer produces SPARKS during operation. NEVER use the nailer near flammable substances, gases or vapors including lacquer, paint, benzine, thinner, gasoline, adhesives, mastics, glues or any other material that is -- or the vapors, fumes or byproducts of which are -- flammable, combustible or explosive. Using the nailer in any such environment could cause an EXPLOSION resulting in personal injury or death to user and bystanders.

MAINTAINING THE TOOL

When working on air tools note the warnings in this manual and use extra care when evaluating problem tools.

-3-

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Industrial OIL Free Angled Finish Nailers N52FN/N62FNIndex IntroductionOperation Safety InstructionsAIR Supply and Connections Loading ToolN52FN/N62FN Tool Specifications AIR Supply and Connections Adjusting the MULTI-DIRECTIONAL Exhaust Loading the N52FN/N62FNTo Prevent Accidental Injuries Sequential Trip Operation Tool OperationTrigger Operation Contact Trip OperationTool Must Cycle Tool Operation CheckTrigger Operated Tool Tool Must not CycleReplacement Parts AIR SUPPLY-PRESSURE and VolumeMaintaining the Pneumatic Tool Problem Cause Correction Trouble ShootingDIAL-A-DEPTH Fastener Control Adjustment To Adjust DIAL-A Depthtm Fastener Control AdjustmentJAM Release Accessories Available Page Introducción ÍndiceNota Operación Instrucciones DE SeguridadSuministro DE Aire Y Conexiones AL Cargar LA HerramientaPresión DE Operación Especificaciones DE LAS N52FN/N62FNEspecificaciones DEL Sujetador Conexión DE Aire DE LA HerramientaRegulador ConexionesMangueras Fuente DE SuministroCarga DE LOS Clavos Carga DE LAS Herramientas N52FN/N62FNDeflector Direccional DE LA Salida Advertencia Para Impedir Lesiones AccidentalesOperación DE Disp ARO Secuencial Operación DE LA HerramientaAntes DE Manejar U Operar Esta Herramienta Operación DE Disp ARO POR ContactoLA Herramienta no Debe Efectuar SU Ciclo Verificación DE LA Operación DE LA HerramientaHerramienta Operada POR Gatillo Operación POR Disp ARO SecuencialPresión Y Volumen DEL Suministro DE Aire Mantenimiento DE LA Herramienta NeumáticaPartes DE Reemplazo Diagnóstico DE Falla ProblemaAjuste DEL Control DE Fondo DEL Sujetador DIAL-A-DEPTH Para Ajustar EL Control DE Fondo DEL Sujetador DIAL-A-DEPTHRemueva EL Sujetador Atascado Remarque SommaireFonctionnement Consignes DE SécuritéAlimentation EN AIR Comprimé ET Raccordement Chargement DE L’APPAREILOpération Caractéristiques DES N52FN ET N62FNAlimentation EN AIR Comprimé ET Raccordement Chargement DES Clous Endroit Chargement DU N52FN OU DU N62FNDéflecteur D’ÉCHAPPEMENT Directionnel Pour Prévenir UN AccidentFonctionnement DE L’APPAREIL Mode D’EMPLOISystème DE Sécurité AU COUP-PAR-COUP Vérification DU Système DE DéclenchementDéclenchement P AR LA Détente Système DE Sécurité À LA Volée C.TPièces DE Rechange Alimentation D’AIR Pression VolumeProblème Cause Correction Problèmes DE FonctionnementPour Régler LE DIAL-A-DEPTH Enlevez LE Clou Coince

N52FN, N62FN specifications

The Quantaray N62FN and N52FN are versatile and affordable options for photography enthusiasts seeking to expand their creative toolbox without breaking the bank. These models are particularly suited for those who appreciate a blend of functionality, innovation, and ease of use in their photographic equipment.

The Quantaray N62FN is designed primarily for Nikon users, providing compatibility with a wide range of Nikon DSLR cameras. This lens features a focal length of 18-55mm, making it an excellent choice for everyday photography, from landscapes to portraits. The f/3.5-5.6 aperture ensures that users can capture images in a variety of lighting conditions, while the lightweight construction allows for easy portability. This lens also incorporates a 7-blade diaphragm, which creates beautiful bokeh in out-of-focus areas, enhancing the overall aesthetic of images.

The Quantaray N52FN lens, also compatible with Nikon cameras, offers a longer focal range of 55-200mm, making it ideal for capturing subjects from a distance, such as wildlife or sports events. This telephoto lens features a similar f/4-5.6 aperture, providing notable performance in both bright and low-light environments. Additionally, both models incorporate multi-coated lens elements that help reduce flares and ghosting, ensuring sharp, clear images with vibrant colors.

Both the N62FN and N52FN utilize a lightweight and durable design, allowing photographers to carry them comfortably for prolonged periods. They feature a robust build quality that withstands the rigors of frequent use in various shooting scenarios. The intuitive manual focus mechanism on both lenses provides a smooth and precise experience, while the autofocus capabilities ensure quick and efficient subject acquisition for dynamic photography needs.

In terms of technology, both lenses are built with advanced optical design principles, ensuring that they deliver exceptional image quality across the entire zoom range. The inclusion of aspherical lens elements in their construction minimizes distortion and aberrations, resulting in images that are clear and richly detailed.

Overall, the Quantaray N62FN and N52FN are powerful tools for photographers looking to enhance their imaging capabilities. Their balance of quality, performance, and affordability makes these lenses an appealing choice for both novice and experienced photographers alike, catering to a diverse array of photographic needs and styles.
Top Page Image Contents