Grizzly G0659 Moving & Placing, Leveling Machine, Tools Needed Qty, To level the machine

Page 14

Moving & Placing

This bandsaw is a heavy machine. Serious per- sonal injury may occur if safe moving methods are not used. To be safe, get assistance and use power equipment rated for over 750 lbs. to move the ship- ping crate and remove the machine from the crate.

To lift and move the bandsaw:

1.Remove the chip tray from the bandsaw base.

2.Position the forklift forks under the bandsaw base, as shown in Figure 5.

Figure 5. Lifting bandsaw on forklift forks.

-12-

Leveling Machine

Tools Needed:

Qty

Wrench 19mm

1

Level

1

Once your new machine is in place, it must be lev- eled. The four corners of the machine base have leveling bolts for this purpose.

To level the machine:

1.Loosen the lock nuts on all four corners, then adjust the leveling bolts until all four touch the floor (Figure 6).

Leveling Bolt

Lock Nut

Figure 6. Leveling feet.

2.Using a level as a guide, level the machine by adjusting one side up or down, as needed. Turn the leveling bolt clockwise to lift the foot and counterclockwise to lower the foot. Be sure to adjust each side in small, equal incre- ments.

3.Once the machine is level in one direction, rotate the level 90˚ and check again for level.

4.Again adjust the feet as needed. Be sure to use small, equal increments on each side.

5.Re-check for level in both the left-to-right and front-to-rear directions. Re-adjust if neces- sary.

6.Once the machine is level, tighten the level- ing lock nuts, taking care to not turn the lev- ling bolts.

G06599" x 14" Vertical Metal-Cutting Bandsaw

Image 14
Contents Model G0659 Ss ,EAD from Leadbased PAINTS Table of Contents Contact Info IntroductionForeword Functional Overview Identification Machine Data Sheet Main Specifications Cutting Capacity #4/..3!&%49  !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%293AFETYYNSTRUCTIONSSFORR-ACHINERY Safety Instructions for Metal Cutting Bandsaws 220V Single-Phase Circuit RequirementsUnpacking SetupSetup Safety Inventory Main Components Figure QtySite Considerations Clean UpPlacement Location Floor LoadTools Needed Qty Moving & PlacingLeveling Machine To level the machineBolting to Concrete Floors Mounting to Shop FloorRemoving Shipping Bracket To remove the shipping bracketAssembly To assemble the bandsawTest Run Recommended AdjustmentsFactory adjustments that should be verified To test run the machineOperation Safety Basic Controls OperationsCounterweight controls Upper Wheel Tracking Adjustment Adjusts blade trackingClamp Vise Angle AdjustmentsClamp Vise installation Clamp Vise RemovalCutting Depth To adjust the depth of cutTo adjust the feed rate Feed RateTo properly position the guide post To adjust the feed pressureFeed Pressure Guide Post Locking Blade Adjusting Saw Frame StopTo adjust the saw frame stop To lock the blade in the forward positionBlade Length Blade SelectionBlade Terminology Blade WidthTooth Set Tooth TypeBlade Pitch TPI To select the correct blade pitchBlade Care Blade BreakageBlade Care Break-In Blade Break-InTo correctly tension the blade Blade TensioningBlade Changes Adjusting Blade Guides Upper and Lower Guide Bearing AdjustmentLower Blade Guide Assembly Adjustment To position the lower blade guide assemblyBlade Tracking Upper Blade Guide Assembly AdjustmentTo position the upper blade guide assembly To change the blade speed Changing SpeedsChanges in the blade tension may change the blade tracking Tanks, Cylinders, Containers, Valves, Etc Workpiece InspectionCutting Tips Straight Cuts Freehand Cuts To prepare the G0659 for freehand cutsAppearance Chip Inspection ChartAdditional ActionsG7315-Super Heavy-Duty Mobile Base AccessoriesGrizzly Bandsaw Blades G1928-Bandsaw HandbookSchedule MaintenanceCleaning Redressing Rubber TiresLubrication Chip TrayMotor & Electrical ServiceTroubleshooting Cutting Operations MiscellaneousTo align the V-belt pulleys TensioningReplacing V-Belt To check/replace the V-beltTo check if the wheels are parallel and copla- nar Wheel AlignmentMaterials Needed Qty Upper wheel adjustments To adjust the wheel coplanarityTo adjust the blade scraper and brush Blade Scraper Wheel BrushG0659 Wiring Diagram 110 VACMotor junction box wiring G0659 Electrical ComponentsG0659 Hydraulic System Schematic See FigureUpper Saw Frame Breakdown Upper Saw Frame Parts List DescriptionLower Saw Frame Breakdown and Parts List Gearbox Breakdown and Parts List Drive Unit Breakdown and Parts List Table Base Parts Breakdown Table Base Parts List Cabinet Base Breakdown and Parts List Safety Labels Breakdown and Parts List 22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7!  Warranty and Returns #ALL 4ODAYD&ORO! &2%%