Grizzly G0659 owner manual Assembly, To assemble the bandsaw

Page 16

Assembly

To assemble the bandsaw:

1.Attach one of the roller brackets with two hex bolts and lock washers, as shown in Figure 9.

Lock Washer

Hex Bolt

 

Roller Bracket

 

 

 

Figure 9. Roller bracket.

2.Slide one end of the roller into the attached bracket, slide the other bracket over the other end of the roller, then attach the bracket to the table with the remaining hex bolts and lock washers (Figure 10).

Mounting Bracket

Roller

Figure 10. Mounting roller.

3.Slide the counterweight onto the counter- weight rail and secure in position with the lock knob (Figure 11).

Counterweight Rail

Lock Knob Counterweight

Figure 11. Counterweight installation.

4.Twist the knob onto the saw frame release lever until it is snug (Figure 12).

Saw Frame

Release Lever

Knob

Figure 12. Saw frame release lever knob.

-14-

G06599" x 14" Vertical Metal-Cutting Bandsaw

Image 16
Contents Model G0659 Ss ,EAD from Leadbased PAINTS Table of Contents Foreword Functional Overview IntroductionContact Info Identification Machine Data Sheet Main Specifications Cutting Capacity #4/..3!&%49  !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%293AFETYYNSTRUCTIONSSFORR-ACHINERY Safety Instructions for Metal Cutting Bandsaws 220V Single-Phase Circuit RequirementsSetup Setup Safety InventoryUnpacking Main Components Figure QtyClean Up Placement LocationSite Considerations Floor LoadMoving & Placing Leveling MachineTools Needed Qty To level the machineMounting to Shop Floor Removing Shipping BracketBolting to Concrete Floors To remove the shipping bracketAssembly To assemble the bandsawRecommended Adjustments Factory adjustments that should be verifiedTest Run To test run the machineOperation Safety Basic Controls OperationsCounterweight controls Upper Wheel Tracking Adjustment Adjusts blade trackingAngle Adjustments Clamp Vise installationClamp Vise Clamp Vise RemovalTo adjust the depth of cut To adjust the feed rateCutting Depth Feed RateFeed Pressure Guide Post To adjust the feed pressureTo properly position the guide post Adjusting Saw Frame Stop To adjust the saw frame stopLocking Blade To lock the blade in the forward positionBlade Selection Blade TerminologyBlade Length Blade WidthTooth Set Tooth TypeBlade Pitch TPI To select the correct blade pitchBlade Breakage Blade Care Break-InBlade Care Blade Break-InBlade Changes Blade TensioningTo correctly tension the blade Adjusting Blade Guides Upper and Lower Guide Bearing AdjustmentLower Blade Guide Assembly Adjustment To position the lower blade guide assemblyTo position the upper blade guide assembly Upper Blade Guide Assembly AdjustmentBlade Tracking Changes in the blade tension may change the blade tracking Changing SpeedsTo change the blade speed Cutting Tips Workpiece InspectionTanks, Cylinders, Containers, Valves, Etc Straight Cuts Freehand Cuts To prepare the G0659 for freehand cutsChip Inspection Chart AdditionalAppearance ActionsAccessories Grizzly Bandsaw BladesG7315-Super Heavy-Duty Mobile Base G1928-Bandsaw HandbookMaintenance CleaningSchedule Redressing Rubber TiresLubrication Chip TrayTroubleshooting ServiceMotor & Electrical Cutting Operations MiscellaneousTensioning Replacing V-BeltTo align the V-belt pulleys To check/replace the V-beltMaterials Needed Qty Wheel AlignmentTo check if the wheels are parallel and copla- nar Upper wheel adjustments To adjust the wheel coplanarityTo adjust the blade scraper and brush Blade Scraper Wheel BrushG0659 Wiring Diagram 110 VACMotor junction box wiring G0659 Electrical ComponentsG0659 Hydraulic System Schematic See FigureUpper Saw Frame Breakdown Upper Saw Frame Parts List DescriptionLower Saw Frame Breakdown and Parts List Gearbox Breakdown and Parts List Drive Unit Breakdown and Parts List Table Base Parts Breakdown Table Base Parts List Cabinet Base Breakdown and Parts List Safety Labels Breakdown and Parts List 22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!- 7!  Warranty and Returns #ALL 4ODAYD&ORO! &2%%