Grizzly G0659 owner manual Safety Labels Breakdown and Parts List

Page 56

Safety Labels Breakdown and Parts List

243

250

244

249

245

248

	(Next to Power Cords)

		246


246				247

REF	PART #	DESCRIPTION

243	P0659243	MACHINE ID LABEL
244	P0659244	EYE INJURY HAZARD LABEL
245	P0659245	DISCONNECT FROM POWER LABEL
246	PLABEL-14	ELECTRICITY LABEL

REF	PART #	DESCRIPTION

247	P0659247	GRIZZLY LABEL PLATE
248	P0659248	DOOR INJURY LABEL
249	P0659249	BLADE WARNING LABEL
250	PLABEL-12	READ MANUAL 2" X 3 5/16"

Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact Grizzly at (800) 523-4777 or www.grizzly.com to order new labels.

-54-	G0659 9" x 14" Vertical Metal-Cutting Bandsaw

Image 56

Contents Model G0659 Ss ,EAD from Leadbased PAINTS Table of Contents Contact Info IntroductionForeword Functional Overview Identification Machine Data Sheet Main Specifications Cutting Capacity #4/..3!&%49 !,7!93 53%3 %!2.2 02/4%#4/ %. /0%2!4.! -!#.%293AFETYYNSTRUCTIONSSFORR-ACHINERY Safety Instructions for Metal Cutting Bandsaws 220V Single-Phase Circuit RequirementsSetup Setup Safety InventoryUnpacking Main Components Figure QtyClean Up Placement LocationSite Considerations Floor LoadMoving & Placing Leveling MachineTools Needed Qty To level the machineMounting to Shop Floor Removing Shipping BracketBolting to Concrete Floors To remove the shipping bracketAssembly To assemble the bandsawRecommended Adjustments Factory adjustments that should be verifiedTest Run To test run the machineOperation Safety Basic Controls OperationsCounterweight controls Upper Wheel Tracking Adjustment Adjusts blade trackingAngle Adjustments Clamp Vise installationClamp Vise Clamp Vise RemovalTo adjust the depth of cut To adjust the feed rateCutting Depth Feed RateTo properly position the guide post To adjust the feed pressureFeed Pressure Guide Post Adjusting Saw Frame Stop To adjust the saw frame stopLocking Blade To lock the blade in the forward positionBlade Selection Blade TerminologyBlade Length Blade WidthTooth Set Tooth TypeBlade Pitch TPI To select the correct blade pitchBlade Breakage Blade Care Break-InBlade Care Blade Break-InTo correctly tension the blade Blade TensioningBlade Changes Adjusting Blade Guides Upper and Lower Guide Bearing AdjustmentLower Blade Guide Assembly Adjustment To position the lower blade guide assemblyBlade Tracking Upper Blade Guide Assembly AdjustmentTo position the upper blade guide assembly To change the blade speed Changing SpeedsChanges in the blade tension may change the blade tracking Tanks, Cylinders, Containers, Valves, Etc Workpiece InspectionCutting Tips Straight Cuts Freehand Cuts To prepare the G0659 for freehand cutsChip Inspection Chart AdditionalAppearance ActionsAccessories Grizzly Bandsaw BladesG7315-Super Heavy-Duty Mobile Base G1928-Bandsaw HandbookMaintenance CleaningSchedule Redressing Rubber TiresLubrication Chip TrayMotor & Electrical ServiceTroubleshooting Cutting Operations MiscellaneousTensioning Replacing V-BeltTo align the V-belt pulleys To check/replace the V-beltTo check if the wheels are parallel and copla- nar Wheel AlignmentMaterials Needed Qty Upper wheel adjustments To adjust the wheel coplanarityTo adjust the blade scraper and brush Blade Scraper Wheel BrushG0659 Wiring Diagram 110 VACMotor junction box wiring G0659 Electrical ComponentsG0659 Hydraulic System Schematic See FigureUpper Saw Frame Breakdown Upper Saw Frame Parts List DescriptionLower Saw Frame Breakdown and Parts List Gearbox Breakdown and Parts List Drive Unit Breakdown and Parts List Table Base Parts Breakdown Table Base Parts List Cabinet Base Breakdown and Parts List Safety Labels Breakdown and Parts List 22!.49 #!2$ 99.$5342!, .# 0//88 %,,.!-7! Warranty and Returns #ALL 4ODAYD&ORO! &2%%