Woodstock W1829 Setup, Unpacking, Jointer Inventory Figures Qty, Hardware and Tools Not shown

Page 13

Model W1829 (Mfg. Since 9/11)

SETUP

Unpacking

This machine has been carefully packaged for safe transportation. If you notice the machine has been damaged during shipping, please contact your authorized Shop Fox dealer immediately.

Inventory

The following is a description of the main components shipped with the Model W1829. Lay the components out to inventory them.

Note: If you can't find an item on this list, check the mounting location on the machine or examine the packaging materials carefully. Occasionally we pre-install certain components for safer shipping.

Jointer Inventory: (Figures 4–5)		Qty
A.	Jointer Bed Assembly	1
B.	Fence	1
C.	Dust Collection Bag	1
D.	Push Blocks	2
E.	Fence Tilting Handle	1
F.	Fence Bracket Assembly	1
G.	Fence Sliding Handle	1
H.	Locking Plate Assembly	1
I.	Fence Support	1
J.	Dust Chute	1
K.	Dust Collection Bag Clamp	1

Keep machine disconnected from power until instructed otherwise.

A

B

Figure 4. Large components.

SETUP

Hardware and Tools (Not shown)
—Cap Screws M8-1.25 x 20	6
—Lock Washers 8mm	6
—Hex Wrench 4mm	1
—Hex Wrench 6mm	1

K

J

I

H

G

C

F

D

E

Figure 5. Small components.

-11-

Image 13

Contents OWNERS MANUAL Page Contents Woodstock Technical Support IntroductionAbout Your Machine Model W1829 Model W1829 Mfg. Since 9/11 W1829 identification-rear view Controls & FeaturesStandard Machinery Safety Instructions SafetySafety Additional Safety for Jointers Circuit Requirements ElectricalFull-Load Current Rating Circuit Requirements forExtension Cords Grounding RequirementsFor 110V Connection Unpacking SetupInventory Jointer Inventory Figures QtyMachine dimensions Machine Placement Cleaning MachineExample of a direct mount Bench MountingTo assemble the jointer, do these steps AssemblyFence positioned over Jointer tables To install the dust port and collection bag, do these steps Recommended AdjustmentsDust Collection Recommended CFM at Dust PortConnecting Power Power ConnectionTo test run the machine, do these steps Test RunGeneral OperationsBasic Controls Stock Inspection Requirements Correct setting for grain AlignmentSurface plane on the jointer Squaring StockJointer Surface PlaningTo edge joint on the jointer, do these steps Edge JointingTo bevel cut on the jointer, do these steps Bevel CuttingD3319-6 Replacement Jointer Knives Set AccessoriesD3640-Shop Fox Tool Table Plus W1218A-RotacatorW1041-3 x 2 1⁄2 Adapters W1044-4 x 2 1⁄2 Adapters D2675-Safety Glasses D2676-Adjustable Safety GlassesCleaning MaintenanceTable & Base BeltsTroubleshooting ServiceMotor & Electrical Operation Adjusting Knife height Checking/Adjusting Knife HeightChecking Knife Height Tools Needed QtyKnives Laceration injuries may occur. UseCutterhead clamp screw Location Replacing KnivesSetting 90 Fence Angle Stop Setting Fence Angle StopsChecking the inward 45º stop Inward Stop Bolt Setting 45 Inward StopOutward stop bolt detail Setting 45 Outward StopTo realign or replace the cutterhead belt, do these steps Belt ReplacementTo replace motor brushes, do these steps Motor Brush ReplacementWiring Diagram Color KEY Electrical Safety Instructions110 VAC Wiring DiagramMain PartsDescription Parts ListLabels Parts Woodstock international inc. p.o. box Bellingham, Wa Warranty High Quality Machines and Tools