Woodstock W1829 manual Operations, General, Basic Controls

Page 21

Model W1829 (Mfg. Since 9/11)

OPERATIONS

General

This machine will perform many types of operations that are beyond the scope of this manual. Many of these operations can be dangerous or deadly if performed incorrectly.

The instructions in this section are written with the understanding that the operator has the necessary knowledge and skills to operate this machine. If at any time you are experiencing difficulties performing any operation, stop using the machine!

If you are an inexperienced operator, we strongly recommend that you read books or trade articles, or seek training from an experienced jointer operator before performing any unfamiliar operations. Above all, your safety should come first!

READ and understand this entire instruc- tion manual before using this machine. Serious personal injury may occur if safety and operational information is not understood and followed. DO NOT risk your safety by not reading!

Basic Controls

This section covers the basic parts and controls used during routine operations. Refer to Figures 21–­22for basic parts and control locations.

A.ON/OFF Switch: Starts and stops the cutterhead rotation.

The switch has a yellow safety key—removing it locks the switch in the OFF position. Always remove this yellow key when leaving the work area. This prevents unsupervised persons in your shop (especially children) from starting the jointer.

B.Depth of Cut Adjustment Knob: Changes the height of the infeed table to control the depth of cut.

C.Fence Tilting Handle: Locks the fence at the desired angle. Use fence stops to quickly set the fence to 90° (perpendicular to the tables), 45° inward, or 45° outward.

D.Fence Sliding Handle: Allows you to adjust the position of the fence over the tables. ALWAYS tighten it before you begin operations. The position of the fence determines the width of the cut as the workpiece moves over the cutterhead. NEVER operate the jointer if ANY part of cutterhead is exposed on the work area.

-19-

AB

Figure 21. W1829 basic controls in front.

C

D

Figure 22. W1829 basic controls in back.

OPERATIONS

Page 20 Page 22
Image 21
Page 20 Page 22
Contents OWNERS MANUAL Page Contents Introduction Woodstock Technical SupportAbout Your Machine Model W1829 Model W1829 Mfg. Since 9/11 W1829 identification-rear view Controls & FeaturesStandard Machinery Safety Instructions SafetySafety Additional Safety for Jointers Circuit Requirements ElectricalFull-Load Current Rating Circuit Requirements forGrounding Requirements Extension CordsFor 110V Connection Unpacking SetupInventory Jointer Inventory Figures QtyMachine dimensions Machine Placement Cleaning MachineExample of a direct mount Bench MountingTo assemble the jointer, do these steps AssemblyFence positioned over Jointer tables To install the dust port and collection bag, do these steps Recommended AdjustmentsDust Collection Recommended CFM at Dust PortConnecting Power Power ConnectionTo test run the machine, do these steps Test RunOperations GeneralBasic Controls Stock Inspection Requirements Correct setting for grain AlignmentSurface plane on the jointer Squaring StockJointer Surface PlaningTo edge joint on the jointer, do these steps Edge JointingTo bevel cut on the jointer, do these steps Bevel CuttingD3319-6 Replacement Jointer Knives Set AccessoriesD3640-Shop Fox Tool Table Plus W1218A-RotacatorW1041-3 x 2 1⁄2 Adapters W1044-4 x 2 1⁄2 Adapters D2675-Safety Glasses D2676-Adjustable Safety GlassesCleaning MaintenanceTable & Base BeltsService TroubleshootingMotor & Electrical Operation Adjusting Knife height Checking/Adjusting Knife HeightChecking Knife Height Tools Needed QtyKnives Laceration injuries may occur. UseCutterhead clamp screw Location Replacing KnivesSetting 90 Fence Angle Stop Setting Fence Angle StopsChecking the inward 45º stop Inward Stop Bolt Setting 45 Inward StopOutward stop bolt detail Setting 45 Outward StopTo realign or replace the cutterhead belt, do these steps Belt ReplacementTo replace motor brushes, do these steps Motor Brush ReplacementWiring Diagram Color KEY Electrical Safety Instructions110 VAC Wiring DiagramMain PartsDescription Parts ListLabels Parts Woodstock international inc. p.o. box Bellingham, Wa Warranty High Quality Machines and Tools
Top Page Image Contents