Woodstock W1829 manual Belt Replacement, To realign or replace the cutterhead belt, do these steps

Page 38

Model W1829 (Mfg. Since 9/11)

V-Belt Replacement

SERVICE

The Model W1829 uses two belts to drive the cutterhead and the dust collection impeller. When these belts are not tensioned correctly, misaligned, or damaged, your jointer will not function properly.

The part number for the replacement drive belt is X1829070; the part number for the replacement fan belt is X1829092.

Refer to the parts diagram in this manual when fixing belt problems. If you need further assistance, call our Tech Support at (360) 734-3482 or send e-mail to: tech-support@shopfox.biz.

To realign or replace the cutterhead belt, do these steps:

1.DISCONNECT JOINTER FROM POWER!

2.While facing the rear of the jointer, tip it away from you until it rests on the fence assembly.

3.Remove the screws that hold the motor cover to the jointer base. Lift the cover off and set it aside.

4.Inspect the cutterhead belt for proper tension, straight alignment, and possible damage or wear.

Note: The belt is properly tensioned if it deflects about 3⁄8" when you press down on middle of the belt with moderate pressure from your thumb or forefinger. The belt is properly aligned if it lies flat and straight on the motor shaft and drive pulley. Belt damage will be evident upon inspection.

5.Loosen the four motor mounting cap screws (see Figure 49), but do not remove them.

6.Replace a damaged belt with a new one. Realign and re-tension the belt.

7.Tighten the motor mounting screws and replace the motor cover.

8.Test run the jointer, as described on Page 18. If this procedure does not solve the problem, call Tech Support.

Note: The fan belt is installed without releasing motor tension. Simply slide the old belt off. Slide the new belt on and replace the motor cover.

-36-

Motor Mount Screws

Cutterhead Belt

Figure 49. Motor mounting screws and

belt locations.

Page 37 Page 39
Image 38
Page 37 Page 39
Contents OWNERS MANUAL Page Contents About Your Machine IntroductionWoodstock Technical Support Model W1829 Model W1829 Mfg. Since 9/11 Controls & Features W1829 identification-rear viewSafety Standard Machinery Safety InstructionsSafety Additional Safety for Jointers Full-Load Current Rating ElectricalCircuit Requirements Circuit Requirements forFor 110V Connection Grounding RequirementsExtension Cords Inventory SetupUnpacking Jointer Inventory Figures QtyMachine Placement Cleaning Machine Machine dimensionsBench Mounting Example of a direct mountAssembly To assemble the jointer, do these stepsFence positioned over Jointer tables Dust Collection Recommended AdjustmentsTo install the dust port and collection bag, do these steps Recommended CFM at Dust PortPower Connection Connecting PowerTest Run To test run the machine, do these stepsBasic Controls OperationsGeneral Correct setting for grain Alignment Stock Inspection RequirementsSquaring Stock Surface plane on the jointerSurface Planing JointerEdge Jointing To edge joint on the jointer, do these stepsBevel Cutting To bevel cut on the jointer, do these stepsD3640-Shop Fox Tool Table Plus AccessoriesD3319-6 Replacement Jointer Knives Set W1218A-RotacatorD2675-Safety Glasses D2676-Adjustable Safety Glasses W1041-3 x 2 1⁄2 Adapters W1044-4 x 2 1⁄2 AdaptersTable & Base MaintenanceCleaning BeltsMotor & Electrical ServiceTroubleshooting Operation Checking Knife Height Checking/Adjusting Knife HeightAdjusting Knife height Tools Needed QtyLaceration injuries may occur. Use KnivesReplacing Knives Cutterhead clamp screw LocationSetting Fence Angle Stops Setting 90 Fence Angle StopSetting 45 Inward Stop Checking the inward 45º stop Inward Stop BoltSetting 45 Outward Stop Outward stop bolt detailBelt Replacement To realign or replace the cutterhead belt, do these stepsMotor Brush Replacement To replace motor brushes, do these stepsElectrical Safety Instructions Wiring Diagram Color KEYWiring Diagram 110 VACParts MainParts List DescriptionLabels Parts Woodstock international inc. p.o. box Bellingham, Wa Warranty High Quality Machines and Tools
Top Page Image Contents