Woodstock manual Model W1829 Mfg. Since 9/11

Page 6

INTRODUCTION

	Model W1829 (Mfg. Since 9/11)



Table Information
Table Length	28-1/2 in.
Table Width	6-1/4 in.
Table Thickness	1/4 in.
Floor to Table Height	73-1/4 in.
Table Adjustment Type	Knob
Table Movement Type	Swing
Construction
Base	Pre-formed Steel
Body Assembly	Pre-formed Steel
Fence Assembly	Cast Iron
Guard	Aluminum
Table	Precision-Ground Cast Iron
Paint	Powder Coated
Other Information
Number of Dust Ports	1
Dust Port Size	2-1/2 in.
Product Dimensions
Weight	76 lbs.
Width (side-to-side) x Depth (front-to-back) x Height	24 x 6 x 7-3/4 in.
Footprint (Length x Width)	18-7/8 x 11 in.
Shipping Dimensions
Type	Cardboard
Content	Machine
Weight	80 lbs.
Length x Width x Height	26 x 8 x 10 in.
Electrical
Power Requirement	110V, Single-Phase, 60 Hz
Minimum Circuit Size	15 Amp
Cord Length	8 ft.
Cord Gauge	16 AWG
Plug Included	Yes
Included Plug Type	NEMA 5-15
Other
Country Of Origin	China
Warranty	2 Year
Assembly Time	30 Minutes
Features
45 Degree Inward, 90 and 45 Degree Outward Stops
Jack Screw Knife Adjustment
2-1/2" Dust Port
2 Safety Push Blocks
Dust Collection Fan, Chute and Bag

-4-

Image 6

Contents OWNERS MANUAL Page Contents Introduction Woodstock Technical SupportAbout Your Machine Model W1829 Model W1829 Mfg. Since 9/11 Controls & Features W1829 identification-rear viewSafety Standard Machinery Safety InstructionsSafety Additional Safety for Jointers Full-Load Current Rating ElectricalCircuit Requirements Circuit Requirements forGrounding Requirements Extension CordsFor 110V Connection Inventory SetupUnpacking Jointer Inventory Figures QtyMachine Placement Cleaning Machine Machine dimensionsBench Mounting Example of a direct mountAssembly To assemble the jointer, do these stepsFence positioned over Jointer tables Dust Collection Recommended AdjustmentsTo install the dust port and collection bag, do these steps Recommended CFM at Dust PortPower Connection Connecting PowerTest Run To test run the machine, do these stepsOperations GeneralBasic Controls Correct setting for grain Alignment Stock Inspection RequirementsSquaring Stock Surface plane on the jointerSurface Planing JointerEdge Jointing To edge joint on the jointer, do these stepsBevel Cutting To bevel cut on the jointer, do these stepsD3640-Shop Fox Tool Table Plus AccessoriesD3319-6 Replacement Jointer Knives Set W1218A-RotacatorD2675-Safety Glasses D2676-Adjustable Safety Glasses W1041-3 x 2 1⁄2 Adapters W1044-4 x 2 1⁄2 AdaptersTable & Base MaintenanceCleaning BeltsService TroubleshootingMotor & Electrical Operation Checking Knife Height Checking/Adjusting Knife HeightAdjusting Knife height Tools Needed QtyLaceration injuries may occur. Use KnivesReplacing Knives Cutterhead clamp screw LocationSetting Fence Angle Stops Setting 90 Fence Angle StopSetting 45 Inward Stop Checking the inward 45º stop Inward Stop BoltSetting 45 Outward Stop Outward stop bolt detailBelt Replacement To realign or replace the cutterhead belt, do these stepsMotor Brush Replacement To replace motor brushes, do these stepsElectrical Safety Instructions Wiring Diagram Color KEYWiring Diagram 110 VACParts MainParts List DescriptionLabels Parts Woodstock international inc. p.o. box Bellingham, Wa Warranty High Quality Machines and Tools