Woodstock W1829 manual Labels

Page 44

Model W1829 (Mfg. Since 9/11)

Parts List (continued)

REF	PART #	DESCRIPTION
106	X1829106	RIGHT RUBBER FOOT
107	X1829107	LEFT RUBBER FOOT
108	X1829108	GUARD PLATE
109	X1829109	CUTTERHEAD COVER
110	XPS19M	PHLP HD SCR M5-.8 X 6

REF	PART #	DESCRIPTION
111	XPCAP68M	CAP SCREW M6-1 X 8
112	X1829112	FENDER WASHER 5MM
113	X1829113	INFEED TABLE SUPPORT ARM
114	X1829114	CHIP COLLECTOR COVER PLATE
115	X1829115	WIRE RESTRAINT

Labels

PARTS

Safety labels warn about machine hazards and how to prevent machine damage or injury. The owner of this machine MUST maintain the original location and readability of all labels on this machine. If any label is removed or becomes unreadable, REPLACE that label before allowing the machine to enter service again. Contact Woodstock International, Inc. at (360) 734-3482 or www.shopfoxtools.com to order new labels.

NOTE: Align this label with cutterhead throat.

121

117

122

119

120	116

118

REF	PART #	DESCRIPTION		REF	PART #	DESCRIPTION
116	XLABEL-08A	READ MANUAL LABEL		120	X1829120	MACHINE ID LABEL
117	X1829117	CUTTERHEAD GUARD LABEL		121	X1829121	CUTTERHEAD EXPOSURE LABEL
118	XLABEL-06C	EYE/LUNG HAZARD LABEL		122	XPPAINT-1	SHOP FOX WHITE(M1006)
119	XLABEL-04	ELECTRICITY LABEL

-42-

Image 44

Contents OWNERS MANUAL Page Contents About Your Machine IntroductionWoodstock Technical Support Model W1829 Model W1829 Mfg. Since 9/11 Controls & Features W1829 identification-rear viewSafety Standard Machinery Safety InstructionsSafety Additional Safety for Jointers Electrical Circuit RequirementsFull-Load Current Rating Circuit Requirements forFor 110V Connection Grounding RequirementsExtension Cords Setup UnpackingInventory Jointer Inventory Figures QtyMachine Placement Cleaning Machine Machine dimensionsBench Mounting Example of a direct mountAssembly To assemble the jointer, do these stepsFence positioned over Jointer tables Recommended Adjustments To install the dust port and collection bag, do these stepsDust Collection Recommended CFM at Dust PortPower Connection Connecting PowerTest Run To test run the machine, do these stepsBasic Controls OperationsGeneral Correct setting for grain Alignment Stock Inspection RequirementsSquaring Stock Surface plane on the jointerSurface Planing JointerEdge Jointing To edge joint on the jointer, do these stepsBevel Cutting To bevel cut on the jointer, do these stepsAccessories D3319-6 Replacement Jointer Knives SetD3640-Shop Fox Tool Table Plus W1218A-RotacatorD2675-Safety Glasses D2676-Adjustable Safety Glasses W1041-3 x 2 1⁄2 Adapters W1044-4 x 2 1⁄2 AdaptersMaintenance CleaningTable & Base BeltsMotor & Electrical ServiceTroubleshooting Operation Checking/Adjusting Knife Height Adjusting Knife heightChecking Knife Height Tools Needed QtyLaceration injuries may occur. Use KnivesReplacing Knives Cutterhead clamp screw LocationSetting Fence Angle Stops Setting 90 Fence Angle StopSetting 45 Inward Stop Checking the inward 45º stop Inward Stop BoltSetting 45 Outward Stop Outward stop bolt detailBelt Replacement To realign or replace the cutterhead belt, do these stepsMotor Brush Replacement To replace motor brushes, do these stepsElectrical Safety Instructions Wiring Diagram Color KEYWiring Diagram 110 VACParts MainParts List DescriptionLabels Parts Woodstock international inc. p.o. box Bellingham, Wa Warranty High Quality Machines and Tools