Woodstock W1829 manual Setting 45 Inward Stop, Checking the inward 45º stop Inward Stop Bolt

Page 36

Model W1829 (Mfg. Since 9/11)

SERVICE

Setting 45° Inward Stop

1.DISCONNECT JOINTER FROM POWER!

2.With the fence positioned over the bed and the sliding handle locked, loosen the fence tilting handle and release the limit tab.

3.Tilt the fence towards the table as far as it will go, then tighten the fence tilting handle.

Note: When you tilt the fence towards the table, it will stop when it hits the inward stop bolt.

4.Use a combination square to check the angle of the fence, as shown in Figure 45.

—If the fence leans 45º towards the table, the inward 45º stop is set correctly; proceed to set the outward 45º stop (see Page 35).

—If the fence does not lean 45º towards the table, adjust the inward 45º stop by performing Steps 5–9.

5.Loosen the fence tilting handle, bring the fence to 45º, then tighten the handle just enough to keep the fence in position.

6.Remove the limit block from the fence bracket assembly and set it aside.

7.Using two 8mm wrenches, adjust the inward stop bolt (see Figure 46) until it contacts the fence at precisely 45º inward, then tighten the jam nut (where the bolt meets the bracket assembly) while holding the stop bolt in place. Some trial-and-error will be required to set this stop correctly.

8.Use two 8mm wrenches to tighten the hex nut on the inward stop as you hold the stop in place.

9.Put the limit block back, bring the fence back to 90º and tighten the tilting handle.

Figure 45. Checking the inward 45º stop.

Inward

Stop Bolt

Figure 46. Adjusting the inward stop bolt.

-34-

Page 35 Page 37
Image 36
Page 35 Page 37
Contents OWNERS MANUAL Page Contents Introduction Woodstock Technical SupportAbout Your Machine Model W1829 Model W1829 Mfg. Since 9/11 Controls & Features W1829 identification-rear viewSafety Standard Machinery Safety InstructionsSafety Additional Safety for Jointers Electrical Circuit RequirementsFull-Load Current Rating Circuit Requirements forGrounding Requirements Extension CordsFor 110V Connection Setup UnpackingInventory Jointer Inventory Figures QtyMachine Placement Cleaning Machine Machine dimensionsBench Mounting Example of a direct mountAssembly To assemble the jointer, do these stepsFence positioned over Jointer tables Recommended Adjustments To install the dust port and collection bag, do these stepsDust Collection Recommended CFM at Dust PortPower Connection Connecting PowerTest Run To test run the machine, do these stepsOperations GeneralBasic Controls Correct setting for grain Alignment Stock Inspection RequirementsSquaring Stock Surface plane on the jointerSurface Planing JointerEdge Jointing To edge joint on the jointer, do these stepsBevel Cutting To bevel cut on the jointer, do these stepsAccessories D3319-6 Replacement Jointer Knives SetD3640-Shop Fox Tool Table Plus W1218A-RotacatorD2675-Safety Glasses D2676-Adjustable Safety Glasses W1041-3 x 2 1⁄2 Adapters W1044-4 x 2 1⁄2 AdaptersMaintenance CleaningTable & Base BeltsService TroubleshootingMotor & Electrical Operation Checking/Adjusting Knife Height Adjusting Knife heightChecking Knife Height Tools Needed QtyLaceration injuries may occur. Use KnivesReplacing Knives Cutterhead clamp screw LocationSetting Fence Angle Stops Setting 90 Fence Angle StopSetting 45 Inward Stop Checking the inward 45º stop Inward Stop BoltSetting 45 Outward Stop Outward stop bolt detailBelt Replacement To realign or replace the cutterhead belt, do these stepsMotor Brush Replacement To replace motor brushes, do these stepsElectrical Safety Instructions Wiring Diagram Color KEYWiring Diagram 110 VACParts MainParts List DescriptionLabels Parts Woodstock international inc. p.o. box Bellingham, Wa Warranty High Quality Machines and Tools
Top Page Image Contents