Woodstock W1829 manual Bevel Cutting, To bevel cut on the jointer, do these steps

Page 26

Model W1829 (Mfg. Since 9/11)

OPERATIONS

Bevel Cutting

The purpose of bevel cutting is to cut a specific angle into the edge of a workpiece (see Figure 34).

The Model W1829 has preset fence stops at 45˚ inward, 90˚, and 45˚ outward (135˚). If your situation requires a different angle, the preset fence stops can be easily adjusted for your needs.

To bevel cut on the jointer, do these steps:

1.Read and understand Safety, beginning on Page 6.

2.Make sure your stock has been inspected for danger- ous conditions as described in the Stock Inspection & Requirements instructions, on Page 20.

3.Set the cutting depth for your operation.

Note: We suggest between 1⁄16" and 1⁄8" for bevel cutting, using a more shallow depth for hard wood species or for wide stock.

4.Make sure your fence is set to the angle of your desired cut.

5.If your workpiece is cupped (warped), place it so the concave side toward the fence.

6.Start the jointer.

7.With a push block in your leading hand, press the workpiece against the table and fence with firm pressure, and feed the workpiece over the cutterhead, as in Figure 35.

Note: If your leading hand gets within 4" of the cutterhead, lift it up and over the cutterhead, and place the push block on the portion of the workpiece that is on the outfeed table. Now, focus your pressure on the outfeed end of the workpiece while feeding, and repeat the same action with your trailing hand when it gets within 4" of the cutterhead. To keep your hands safe, DO NOT let them get closer than 4" from the cutterhead when it is moving!

8.Repeat Step 7 until the angled cut is satisfactory to your needs.

NOTICE

If you are not experienced with a jointer, set the depth of cut to 0", and practice feeding the workpiece across the tables as described below. This procedure will better prepare you for the actual operation.

Portion

Removed With

Jointer

Figure 34. Illustration of bevel cutting

results.

Figure 35. Typical bevel cutting operation.

-24-

Page 25 Page 27
Image 26
Page 25 Page 27
Contents OWNERS MANUAL Page Contents About Your Machine IntroductionWoodstock Technical Support Model W1829 Model W1829 Mfg. Since 9/11 Controls & Features W1829 identification-rear viewSafety Standard Machinery Safety InstructionsSafety Additional Safety for Jointers Full-Load Current Rating ElectricalCircuit Requirements Circuit Requirements forFor 110V Connection Grounding RequirementsExtension Cords Inventory SetupUnpacking Jointer Inventory Figures QtyMachine Placement Cleaning Machine Machine dimensionsBench Mounting Example of a direct mountAssembly To assemble the jointer, do these stepsFence positioned over Jointer tables Dust Collection Recommended AdjustmentsTo install the dust port and collection bag, do these steps Recommended CFM at Dust PortPower Connection Connecting PowerTest Run To test run the machine, do these stepsBasic Controls OperationsGeneral Correct setting for grain Alignment Stock Inspection RequirementsSquaring Stock Surface plane on the jointerSurface Planing JointerEdge Jointing To edge joint on the jointer, do these stepsBevel Cutting To bevel cut on the jointer, do these stepsD3640-Shop Fox Tool Table Plus AccessoriesD3319-6 Replacement Jointer Knives Set W1218A-RotacatorD2675-Safety Glasses D2676-Adjustable Safety Glasses W1041-3 x 2 1⁄2 Adapters W1044-4 x 2 1⁄2 AdaptersTable & Base MaintenanceCleaning BeltsMotor & Electrical ServiceTroubleshooting Operation Checking Knife Height Checking/Adjusting Knife HeightAdjusting Knife height Tools Needed QtyLaceration injuries may occur. Use KnivesReplacing Knives Cutterhead clamp screw LocationSetting Fence Angle Stops Setting 90 Fence Angle StopSetting 45 Inward Stop Checking the inward 45º stop Inward Stop BoltSetting 45 Outward Stop Outward stop bolt detailBelt Replacement To realign or replace the cutterhead belt, do these stepsMotor Brush Replacement To replace motor brushes, do these stepsElectrical Safety Instructions Wiring Diagram Color KEYWiring Diagram 110 VACParts MainParts List DescriptionLabels Parts Woodstock international inc. p.o. box Bellingham, Wa Warranty High Quality Machines and Tools
Top Page Image Contents