Woodstock W1829 manual Machine Placement Cleaning Machine, Machine dimensions

Page 14

 

Model W1829 (Mfg. Since 9/11)

Machine Placement

Cleaning Machine

SETUP

•Workbench Load: Refer to the Machine Specifications, on Page 3, for the weight and footprint specifications of your machine. Some workbenches may require additional reinforcement to support both the weight of the machine and materials.

•Working Clearances: Consider the size of material to be processed through the machine, space for auxiliary stands, work tables and other machinery when establishing a location for your Jointer. See Figure 6 for the overall machine measurements.

21"

29"

Figure 6. Machine dimensions.

USE helpers or power lift- ing equipment to lift this 6" Jointer. Otherwise, serious personal injury may occur.

MAKE your shop “child safe.” Close and lock all entrances when you are away. NEVER allow untrained visitors in your shop when assembling, adjusting or operating equipment.

The tables and other unpainted parts of your jointer are coated with a waxy grease that protects them from corrosion during shipment. Clean this grease off with a solvent cleaner or citrus-based degreaser. DO NOT use chlorine- based solvents such as brake parts cleaner or acetone—if you happen to splash some onto a painted surface, you will ruin the finish.

NEVER clean with gasoline or other petroleum- based solvents. Most have low flash points, which make them extremely flammable. A risk of explosion and burning exists if these products are used. Serious personal injury may occur if this warning is ignored!

ALWAYS work in well- ventilated areas far from possible ignition sources when using solvents to clean machinery. Many solvents are toxic when inhaled or ingested. Use care when disposing of waste rags and towels to be sure they DO NOT create fire or environmental hazards.

-12-

Page 13 Page 15
Image 14
Page 13 Page 15
Contents OWNERS MANUAL Page Contents About Your Machine IntroductionWoodstock Technical Support Model W1829 Model W1829 Mfg. Since 9/11 Controls & Features W1829 identification-rear viewSafety Standard Machinery Safety InstructionsSafety Additional Safety for Jointers Full-Load Current Rating ElectricalCircuit Requirements Circuit Requirements forFor 110V Connection Grounding RequirementsExtension Cords Inventory SetupUnpacking Jointer Inventory Figures QtyMachine Placement Cleaning Machine Machine dimensionsBench Mounting Example of a direct mountAssembly To assemble the jointer, do these stepsFence positioned over Jointer tables Dust Collection Recommended AdjustmentsTo install the dust port and collection bag, do these steps Recommended CFM at Dust PortPower Connection Connecting PowerTest Run To test run the machine, do these stepsBasic Controls OperationsGeneral Correct setting for grain Alignment Stock Inspection RequirementsSquaring Stock Surface plane on the jointerSurface Planing JointerEdge Jointing To edge joint on the jointer, do these stepsBevel Cutting To bevel cut on the jointer, do these stepsD3640-Shop Fox Tool Table Plus AccessoriesD3319-6 Replacement Jointer Knives Set W1218A-RotacatorD2675-Safety Glasses D2676-Adjustable Safety Glasses W1041-3 x 2 1⁄2 Adapters W1044-4 x 2 1⁄2 AdaptersTable & Base MaintenanceCleaning BeltsMotor & Electrical ServiceTroubleshooting Operation Checking Knife Height Checking/Adjusting Knife HeightAdjusting Knife height Tools Needed QtyLaceration injuries may occur. Use KnivesReplacing Knives Cutterhead clamp screw LocationSetting Fence Angle Stops Setting 90 Fence Angle StopSetting 45 Inward Stop Checking the inward 45º stop Inward Stop BoltSetting 45 Outward Stop Outward stop bolt detailBelt Replacement To realign or replace the cutterhead belt, do these stepsMotor Brush Replacement To replace motor brushes, do these stepsElectrical Safety Instructions Wiring Diagram Color KEYWiring Diagram 110 VACParts MainParts List DescriptionLabels Parts Woodstock international inc. p.o. box Bellingham, Wa Warranty High Quality Machines and Tools
Top Page Image Contents