Woodstock W1829 manual Laceration injuries may occur. Use, Knives

Page 33

Model W1829 (Mfg. Since 9/11)

6.Move the straightedge to position A, as shown in Figure 39. Turn the jack screw nearest the fence

counterclockwise until the end of the knife touches Cutterhead knives are sharp and

the straightedge.

laceration injuries may occur. Use

7. Move the straightedge to position B, as shown in

caution when handling the cutterhead

knives.

Figure 39. Turn the jack screw nearest the guard

counterclockwise until the end of the knife touches

the straightedge.

Black Lines Represent

8. Slightly tighten the clamp screws, according to the

Straightedge Positions

proper tightening sequence, as shown in Figure 40.

From Overhead View

Repeat Steps 6–7for the other cutterhead knife.

Note: Slightly tightening the clamp screws maintains

A

the knife position while performing the same step

on the other knife. They will be final tightened in a

B

later step.

8.Without disturbing the knife clamp, rotate the Figure 39. Straightedge positions A and B.

cutterhead slightly to check the knife height.

—If the knife moves the straightedge slightly (1/8") forward and back on the table, the knife height is set correctly.

—If the knife does not move the straightedge slightly (1/8") forward and back on the table, continue to make fine adjustments with the jack screws until the knife is set correctly.

10.When the knife heights are set correctly, final tighten each of the knives' clamp screws according to the proper tightening sequence (see Figure 40).

11.Return the cutterhead guard to the operating position and ensure it is working properly.

12.Re-align the fence and tables as needed.

13.Perform a test cut on suitable piece of scrap material.

3

1

2

4

Figure 40. Knife clamp screw tightening

sequence.

SERVICE

-31-

Image 33

Contents OWNERS MANUAL Page Contents Introduction Woodstock Technical SupportAbout Your Machine Model W1829 Model W1829 Mfg. Since 9/11 W1829 identification-rear view Controls & FeaturesStandard Machinery Safety Instructions SafetySafety Additional Safety for Jointers Circuit Requirements ElectricalFull-Load Current Rating Circuit Requirements forGrounding Requirements Extension CordsFor 110V Connection Unpacking SetupInventory Jointer Inventory Figures QtyMachine dimensions Machine Placement Cleaning MachineExample of a direct mount Bench MountingTo assemble the jointer, do these steps AssemblyFence positioned over Jointer tables To install the dust port and collection bag, do these steps Recommended AdjustmentsDust Collection Recommended CFM at Dust PortConnecting Power Power ConnectionTo test run the machine, do these steps Test RunOperations GeneralBasic Controls Stock Inspection Requirements Correct setting for grain AlignmentSurface plane on the jointer Squaring StockJointer Surface PlaningTo edge joint on the jointer, do these steps Edge JointingTo bevel cut on the jointer, do these steps Bevel CuttingD3319-6 Replacement Jointer Knives Set AccessoriesD3640-Shop Fox Tool Table Plus W1218A-RotacatorW1041-3 x 2 1⁄2 Adapters W1044-4 x 2 1⁄2 Adapters D2675-Safety Glasses D2676-Adjustable Safety GlassesCleaning MaintenanceTable & Base BeltsService TroubleshootingMotor & Electrical Operation Adjusting Knife height Checking/Adjusting Knife HeightChecking Knife Height Tools Needed QtyKnives Laceration injuries may occur. UseCutterhead clamp screw Location Replacing KnivesSetting 90 Fence Angle Stop Setting Fence Angle StopsChecking the inward 45º stop Inward Stop Bolt Setting 45 Inward StopOutward stop bolt detail Setting 45 Outward StopTo realign or replace the cutterhead belt, do these steps Belt ReplacementTo replace motor brushes, do these steps Motor Brush ReplacementWiring Diagram Color KEY Electrical Safety Instructions110 VAC Wiring DiagramMain PartsDescription Parts ListLabels Parts Woodstock international inc. p.o. box Bellingham, Wa Warranty High Quality Machines and Tools