Woodstock W1678 instruction manual Warranty and Returns, Specifications

Page 5

Warranty and Returns

Woodstock International, Inc. warrants all SHOP FOX® machinery to be free of defects from workmanship and materials for a period of 2 years from the date of original purchase by the original owner. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or accidents, lack of maintenance, or to repairs or alterations made or specifically authorized by anyone other than Woodstock International, Inc.

Woodstock International, Inc. will repair or replace, at its expense and at its option, the SHOP FOX® machine or machine part which in normal use has proven to be defective, provided that the original owner returns the product prepaid to the SHOP FOX® factory service center or authorized repair facility designated by our Bellingham, WA office, with proof of their purchase of the product within 2 years, and provides Woodstock International, Inc. reasonable opportunity to verify the alleged defect through inspection. If it is determined there is no defect, or that the defect resulted from causes not within the scope of Woodstock International Inc.'s warranty, then the original owner must bear the cost of storing and returning the product.

This is Woodstock International, Inc.'s sole written warranty and any and all warranties that may be implied by law, including any merchantability or fitness, for any particular purpose, are hereby limited to the duration of this written warranty. We do not warrant that SHOP FOX® machinery complies with the provisions of any law or acts. In no event shall Woodstock International, Inc.'s liability under this warranty exceed the purchase price paid for the product, and any legal actions brought against Woodstock International, Inc. shall be tried in the State of Washington, County of Whatcom. We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special or consequential damages arising from the use of our products.

Every effort has been made to ensure that all SHOP FOX® machinery meets high quality and durability standards. We reserve the right to change specifications at any time because of our commitment to continuously improve the quality of our products.

 

 

Specifications

Drum Sander Motor

5 HP, 220 VAC, 25 Amp., 3450 RPM, 60 Hertz, Single-Phase

Drum Drive

Dual V-Belt

Drum Size

6" x 2734"

Drum Surface Speed

2300 FPM

Drum Rotation

Opposite of Feed Conveyor

Conveyor Motor

13 HP, 60 VDC, 2 amp., 60 RPM, Varable Speed

Conveyor Drive

Sprocket and Chain

Conveyor Surface Speed

0-20 FPM

Maximum Lumber Dimensions

..........................................412" Thick x 26" Wide

Minimum Lumber Dimensions

..............................................18" Thick x 9" Long

Dust Port O.D

4"

Conveyor Table Size

2618" x 3014"

Stand

Cabinet Style, Powder Coated Paint

Bearings

Both Serviceable and Permanently-Lubricated Ball Bearings

Power Control

Magnetic Switch, with Emergency Shut-Down

Footprint

36" x 2334"

Shipping Weight

435 lbs.

INTRODUCTION

-3-

Image 5
Contents Model W1678 Page Table of Contents About Your New 26 Double Drum Sander Woodstock Service and SupportIntroduction Specifications Warranty and ReturnsStandard Safety Instructions SafetyKeep proper footing and balance at all times SafetyModel W1678 Additional Safety Instructions for Drum SandersNever stand in the path of potential Workpiece kickback Avoiding Potential InjuriesSafety Grounding 220V OperationExtension Cords Unpacking AssemblyBox Contents Shop Preparation Initial Cleaning Dust Port Handles To install dust ports and handles, do these stepsBeginning To install the crank and handle, do these steps To install the control box, do these stepsControl Box Crank and HandleTo adjust the drum-to-conveyor squareness, do these steps AdjustmentsDrums and Pressure Rollers Unplug the Double Drum Sander30 gauge block positioning Step To adjust the drum-to-conveyor parallelism, do these steps25⁄8 gauge block positioning Part 3 Drum-to-Conveyor Height To adjust the drum-to-conveyor height, do these stepsTo adjust pressure-roller spring tension, do these steps Part 4 Pressure Roller AdjustmentDust scoop gap Dust Scoop GapFront panel and mounting screws Belt TensionConveyor belt hanging gap Conveyor BeltControl panel offers these controls OperationsOverview Control Panel Operation Basic SandingTo use the double drum sander, do these steps Main power ON/OFF safety switchLoad meter Troubleshooting Long grooves General Sanding Belts MaintenanceLubrication MaintenanceSandpaper Replacement Brush ReplacementSlide the bearing out of the bearing block. See Figure Bearing ReplacementBearing-block grease grove Grease port General Cleaning W1678 26 Double Drum Sander Drive System Wiring DiagramControl System Wiring Diagram Closure Parts Scale 143 146 145 144 142 151 154 110 111 106 105 Pressure Roller 227 Side Panel 337 Magnetic Switch Page Page Page BOX BELLINGHAM, WA Warranty Card