Woodstock W1678 instruction manual Part 4 Pressure Roller Adjustment

Page 21

Pressure

Roller

Spring Tension

Adjustment

Pressure

Roller

Height

Adjustment

0.012" to 0.024"

Figure 30. Pressure Roller Adjustment.

Tension Jam Nut

Tension Bolt

 

Height Jam Nut

PRESSURE

 

Height Bolt

ROLLER

 

Figure 31. Pressure roller tension and height

bolts and jam nuts.

PART 4: Pressure Roller Adjustment

Depending on your sanding needs, adjust the pressure roller height and spring tension. See Figure 30.

To adjust pressure-roller height, do these steps:

1.Loosen all six height jam nuts. See Figure 31.

2.Position the 30" gauge block to one side of the conveyor belt and under the three pressure rollers. See Figure 32.

3.Turn the handwheel so the gauge block barely touches the rear drum and the handwheel tape is at the 12:00 position.

4.Now turn the handwheel counter-clockwise exactly 212 turns.

5.Turn the pressure-roller height bolt until the pressure roller just contacts the gauge block. See Figure 31.

6.Hold the height bolt in position and tighten the height jam nut.

7.Repeat Steps 1 through 6 at all rollers, and remove the gauge block.

To adjust pressure-roller spring tension, do these steps:

1.Loosen all six tension jam nuts, and back out the tension bolt completely. See Figure 31.

ADJUSTMENTS

Figure 32. The 30" gauge block positioning.

-19-

NOTICE

Too much pressure roller tension may cause the workpiece to jam.

2.Turn the tension bolt clockwise until it just makes contact with the spring and has resistance.

3.Turn the bolt one additional turn to adjust the spring to a basic spring tension value.

4.Hold the tension bolt in position and tighten the tension jam nut.

5.Repeat Steps 2 through 4 at all rollers.

6.Close and latch the dust hood, and check the V-belt tension.

Image 21
Contents Model W1678 Page Table of Contents Woodstock Service and Support IntroductionAbout Your New 26 Double Drum Sander Specifications Warranty and ReturnsStandard Safety Instructions SafetyKeep proper footing and balance at all times SafetyModel W1678 Additional Safety Instructions for Drum SandersNever stand in the path of potential Workpiece kickback Avoiding Potential InjuriesSafety 220V Operation Extension CordsGrounding Assembly Box ContentsUnpacking Shop Preparation Initial Cleaning To install dust ports and handles, do these steps BeginningDust Port Handles To install the crank and handle, do these steps To install the control box, do these stepsControl Box Crank and HandleTo adjust the drum-to-conveyor squareness, do these steps AdjustmentsDrums and Pressure Rollers Unplug the Double Drum Sander30 gauge block positioning Step To adjust the drum-to-conveyor parallelism, do these steps25⁄8 gauge block positioning Part 3 Drum-to-Conveyor Height To adjust the drum-to-conveyor height, do these stepsTo adjust pressure-roller spring tension, do these steps Part 4 Pressure Roller AdjustmentDust scoop gap Dust Scoop GapFront panel and mounting screws Belt TensionConveyor belt hanging gap Conveyor BeltOperations Overview Control PanelControl panel offers these controls Operation Basic SandingTo use the double drum sander, do these steps Main power ON/OFF safety switchLoad meter Troubleshooting Long grooves General Sanding Belts MaintenanceLubrication MaintenanceSandpaper Replacement Brush ReplacementSlide the bearing out of the bearing block. See Figure Bearing ReplacementBearing-block grease grove Grease port General Cleaning W1678 26 Double Drum Sander Drive System Wiring DiagramControl System Wiring Diagram Closure Parts Scale 143 146 145 144 142 151 154 110 111 106 105 Pressure Roller 227 Side Panel 337 Magnetic Switch Page Page Page BOX BELLINGHAM, WA Warranty Card