Woodstock W1678 Operations, Overview Control Panel, Control panel offers these controls

Page 25

OPERATIONS

Overview

Control Panel

The Model W1678 26" Double Drum Sander accepts stock up to 412" thick by 26" wide, and is capable of completing rough and finish sanding in one pass.

The feed conveyor pushes the workpiece into the infeed side of the sander and under the first pressure roller, which holds the workpiece firmly against the conveyor belt. The front sanding drum sands the workpiece with a

The control panel enables you to turn the conveyor ON/OFF, control the workpiece feed rate, turn the sanding drums ON/OFF, and monitor the sanding load applied by observing the load meter on the control panel. The panel controls are described in detail below. See Figure 42 for control locations.

coarse-grit sandpaper first. Then the workpiece is pushed under the second pressure roller and under the rear sanding drum, which sands the final surface with a finer-grit sandpaper, and then travels out of the sander. During sanding, a dust collector removes sanding dust through the two dust ports.

MODEL W1678

26" DOUBLE DRUM SANDER

INSTRUCTION MANUAL

Phone: 1-360-734-3482On-Line Technical Support: tech-support@shopfox.biz

COPYRIGHT © MARCH, 2003 BY WOODSTOCK INTERNATIONAL, INC.

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT

THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.

Printed in Taiwan

DO NOT operate this sander until you have completed all assembly, and adjustments. Observe all safety precautions, and read and understand this entire manual.

Figure 42. Control Panel.

-23-

The control panel offers these controls:

Sanding Load Meter: Allows you to observe the amperage draw, which indicates the sanding load on the sander so you don’t overload the motor (25 amps is the maximum safe load limit).

NOTE: the load applied on the sander is a balance between conveyor feed rate, sanding drum pressure on the workpiece, grit of sandpaper used, and the species of wood being sanded.

Emergency Stop Button: Allows you to turn the main power ON or OFF to the double drum sander, and shut down the machine in an emergency. Twist clockwise and pull to turn ON, and push to turn the sander OFF.

Conveyor Speed Control Dial: Allows you to adjust the speed at which the feed conveyor pushes the workpiece into the sander from 0- 20 FPM.

Sanding Drum Motor ON and OFF Buttons: Allows you to turn the sanding drums ON or OFF independently of the conveyor.

Conveyor Motor ON and OFF Buttons: Allows you to turn the conveyor belt ON or OFF independently of the sanding drums.

ADJUSTMENTS

Image 25
Contents Model W1678 Page Table of Contents Introduction Woodstock Service and SupportAbout Your New 26 Double Drum Sander Specifications Warranty and ReturnsStandard Safety Instructions SafetyKeep proper footing and balance at all times SafetyModel W1678 Additional Safety Instructions for Drum SandersNever stand in the path of potential Workpiece kickback Avoiding Potential InjuriesSafety Extension Cords 220V OperationGrounding Box Contents AssemblyUnpacking Shop Preparation Initial Cleaning Beginning To install dust ports and handles, do these stepsDust Port Handles To install the crank and handle, do these steps To install the control box, do these stepsControl Box Crank and HandleTo adjust the drum-to-conveyor squareness, do these steps AdjustmentsDrums and Pressure Rollers Unplug the Double Drum Sander30 gauge block positioning Step To adjust the drum-to-conveyor parallelism, do these steps25⁄8 gauge block positioning Part 3 Drum-to-Conveyor Height To adjust the drum-to-conveyor height, do these stepsTo adjust pressure-roller spring tension, do these steps Part 4 Pressure Roller AdjustmentDust scoop gap Dust Scoop GapFront panel and mounting screws Belt TensionConveyor belt hanging gap Conveyor BeltOverview Control Panel OperationsControl panel offers these controls Operation Basic SandingTo use the double drum sander, do these steps Main power ON/OFF safety switchLoad meter Troubleshooting Long grooves General Sanding Belts MaintenanceLubrication MaintenanceSandpaper Replacement Brush ReplacementSlide the bearing out of the bearing block. See Figure Bearing ReplacementBearing-block grease grove Grease port General Cleaning W1678 26 Double Drum Sander Drive System Wiring DiagramControl System Wiring Diagram Closure Parts Scale 143 146 145 144 142 151 154 110 111 106 105 Pressure Roller 227 Side Panel 337 Magnetic Switch Page Page Page BOX BELLINGHAM, WA Warranty Card