Regent Sheffield CSMV80W manual Replacing the light sensor, What to do if . . . What to do if

Page 4
Replacing the light sensor

SMV80 Series IS. 325-1436.qxd 2/16/04 4:38 PM Page 4

Replacing the light sensor

Step 1: Turn off the power at the main fuse/breaker box.

Step 2: Loosen, but do not remove, the lens screws and retaining clips. Remove the glass lens.

Step 3: Remove the bulb from the socket.

Step 4: Remove the reflector screw and remove the reflector.

Step 5: Remove the locknut from the outside of the light sensor.

Step 6: Disconnect wires from the light sensor one at a time. Connect the new light sensor by:

• Connecting black sensor wire to the black supply wire (hot).

Connecting red sensor wire to the black ballast wire.

Connecting white sensor wire to the white supply wire (neutral), white socket wire, and white ballast wire.

Step 7: Replace the locknut on the outside of the light sensor.

Step 8: Replace the reflector and reflector screw, install the bulb, and replace the lens.

Step 9: Turn power back on.

What to do if . . . What to do if . . .

LIGHT DOES NOT COME ON

LIGHT COMES ON FOR ONLY A FEW SECONDS

LIGHT STAYS ON OR

LIGHT COMES ON RANDOMLY

Is there power to the fixture?

Has the house circuit breaker tripped?

Is the wall switch ON?

Is the bulb screwed in completely?

Is the bulb good?

(Be careful not to overtighten.)

Is the light sensor able to determine darkness?

Cover light sensor with electrician’s tape. Wait 2-3 minutes to see if light turns on. If it does,

the sensor is receiving too much light. Install light sensor reflector (E) to deflect light.

Is the wiring to the unit loose?

TURN OFF POWER BEFORE CHECKING.

Is the light sensor sensing reflected light?

Cover light sensor with electrician’s tape. Wait 2-3 minutes. to see if light turns on. If it does, fixture is receiving reflected light. Install light sensor reflector (E) to deflect light.

Is the light sensor in a shaded area?

Shine a flashlight into the light sensor for 2-3 minutes. If the light turns off, the fixture is mounted in an area that does not allow enough

light to enter the light sensor. Install light sen- sor reflector (E) to direct light into sensor.

Is the light sensor good?

Shine a flashlight into the light sensor for 2-3 minutes. If the light does not turn off, replace the light sensor.

4

Image 4
Contents Instrucciones Directives How it works How it works What you need What you needWhat’s included What’s included What to know What to knowTurn OFF the Power at the main fuse/breaker box Wiring your fixture Wiring your fixtureTurn Power OFF at main fuse/breaker box Installing the bulbReplacing the light sensor What to do if . . . What to do ifTwo-year limited warranty Five year limited warranty Authorization Number from the Company will be refusedSMV80 Series is -1436.qxd 2/16/04 438 PM Cómo funciona Cómo funciona Qué se necesita Qué se necesitaQué se incluye Qué se necesita saberInstalación del portalámparas Cableado del portalámparasPara reemplazar el fotosensor Instalación del focoCinco años de garantía limitada Dos años de garantía limitada Rechazado Ce dont vous avez besoin Ce dont vous avez besoin Ce qu’il faut savoirInstallation de l’ampoule Installation de l’ampoule Montage du dispositifEtape 1 Coupez LE Courant au disjoncteur principal Etape 11 RallumerRemplacement du détecteur de lumière Etape 1 Couper le courant à la boîte à fusible principaleEtape 9 Rallumer Que faire siGarantie limitée de deux ans Le détecteur de lumière est-il dans une zone d’ombre?SMV80 Series is -1436.qxd 2/16/04 438 PM