Schneider Electric ATV61 manual Choosing the Altivar 61 catalog number, ATV38 catalog Power Number

Page 6

1. Determining catalog numbers

1. 1. Choosing the Altivar 61 catalog number

Required information (refer to page 5): type of use, line voltage, Altivar 38 catalog number

1. 1. 1. Your catalog number starts with ATV38H

	ATV38 catalog	Power
	number	kW	HP
Power supply	ATV38HU18N4	0.75	1
380…460 V three-phase
	ATV38HU29N4	1.5	2
	ATV38HU41N4	2.2	3
	ATV38HU54N4	3.0	-
	ATV38HU72N4	4.0	5
	ATV38HU90N4	5.5	7.5

	ATV38HD12N4	7.5	10
	ATV38HD16N4	11	15
	ATV38HD23N4	15	20
	ATV38HD25N4 (X)	18.5	25
	ATV38HD28N4 (X)	22	30
	ATV38HD33N4 (X)	30	40
	ATV38HD46N4 (X)	37	50
	ATV38HD54N4 (X)	45	60
	ATV38HD64N4 (X)	55	75

	ATV38HD79N4 (X)	75	100
	ATV38HC10N4 (X)	90	125
	ATV38HC13N4 (X)	110	150
	ATV38HC15N4 (X)	132	200
	ATV38HC19N4 (X)	160	250
	ATV38HC23N4 (X)	200	300

	ATV38HC25N4 (X)	220	350
	ATV38HC28N4 (X)	250	400
	ATV38HC31N4 (X)	280	450
	ATV38HC33N4 (X)	315	500

ATV 61 catalog number	Substitution kit

ATV 61H075N4 (1)	VW3 A9 302

ATV 61HU15N4 (1)	VW3 A9 302
ATV 61HU22N4 (1)	VW3 A9 304
ATV 61HU30N4 (1)	VW3 A9 304
ATV 61HU40N4 (1)	VW3 A9 304
ATV 61HU55N4 (1)	VW3 A9 305

ATV 61HU75N4 (1)	VW3 A9 306
ATV 61HD11N4 (1)	VW3 A9 307
ATV 61HD15N4 (1)	VW3 A9 308
ATV 61HD18N4 (2)	VW3 A9 309
ATV 61HD22N4 (2)	VW3 A9 310
ATV 61HD30N4 (2)	VW3 A9 312
ATV 61HD37N4 (2)	VW3 A9 312
ATV 61HD45N4 (2)	VW3 A9 312
ATV 61HD55N4 (2)	VW3 A9 312

ATV 61HD75N4 (2)	VW3 A9 312
ATV 61HD90N4 (2)
ATV 61HC11N4 (2)
ATV 61HC13N4 (2)
ATV 61HC16N4 (2)
ATV 61HC22N4 (2)

ATV 61HC22N4 (2)
ATV 61HC25N4 (2)
ATV 61HC31N4 (2)
ATV 61HC31N4 (2)

Substitution kit: This kit consists of a metal support plate that makes it possible to re-use the same mounting holes as the ATV38.

(1)Drive supplied with a graphic display terminal that can be connected remotely. To order a drive without a graphic display terminal, add the letter Z at the end of the catalog number. The drive will then be equipped with the integrated 7-segment display terminal.

(2)On ATV38 catalog numbers ending with X, the RFI filter is disconnected in the event of use on an IT system (page 27 implementation).

1. 1. 2. Your catalog number starts with ATV38ED

You must install the Altivar 61 in an enclosure and customize the control devices yourself.

6

Image 6

Contents Altivar Variable-torque applications Table of contents Migration from ATV 38V ATV Altivar 38 hardware identification Your catalog number starts with ATV38H ATV38 catalog Power NumberChoosing the Altivar 61 catalog number Your catalog number starts with ATV38EDSelecting the power circuit options Air exchanger kit VW3A5880x Mounting accessoriesRemovable power terminal kit VW3A5881x Nema type 1 mounting kitControl card fan kit VW3A5882x Separate control card power supply kit VW3A5860xControl circuit options Remote display terminal VW3A58103ATV38 Selecting I/O extension cards VW3A58201, VW3A58202ATV38 and I/O option cards VW3A58201, VW3A58202 PTCVW3A58202 PI feedback or summed reference Three different optionsBecomes ATV VW3... cardCommunication with Profibus bus VW3A58307 Selecting communication channelsCommunication via Modbus network Communication with DeviceNet bus VW3A58309Communication via Ethernet network VW3A58310 Communication with Metasys N2 bus VW3A58354UCommunication with Interbus bus VW3A58304E Communication via Fipio bus VW3A58311Installation Using catalog numbers starting with ATV38HATV 61HU15N4 Comparison of dimensions Width Height DepthATV 61H075N4 ATV 61HU22N4ATV 61HD75N4 ATV 61HD45N4ATV 61HD55N4 ATV 61HD90N4ATV38Hppp product on heatsink Comparison of dimensionsDimensions ATV 61HD30N4, D37N4 D15N4, D18N4D22N4 D45N4, D55N4, D75N4ATV 38Hppp 75 kW and y 315 kW Product on heatsink ATV61HMounting the RFI filter Drive Filter Width Height Depth MountingDrive Width Height Depth MountingComparison of dimensions RFI filtersVW3 Mounting under the drive Side mounting against the ATVATV38Hppppp Nema mounting kitsKit catalog Kit catalog ProductKit for UL Nema Type 1 conformity or IP 21 protection Separate control card power supply Remote display terminalLayout of the ATV38 power terminals Power cablesDisconnecting the RFI filter if using an IT system Connecting to the AltivarCharacteristics of the ATV38 power terminals AWGPC/-, PO, PA/+ Maximum terminal wire size/tightening torqueDrive terminals L1/R, L2/S, L3/T, U/T1, V/T2, W/T3 PA, PBATV61H D90M3X, C13N4 PA, PB RO, SO, toATV61HC16N4 ATV61HC22N4 ATV61H C25N4, C31N4 Control wiring and I/O characteristics Control and option card logic input wiringATV38 value kOhms LI6 wired as PTC probe Encoder Acceptance Installing the communication option cardGeneral Check that the drive is turned offOption card fault Value Description of parameter valuesCommunication via Modbus network Mixed schematicSchematic diagram Calculating the polarization resistorsConfiguring the drive control mode Configuring the driveConfiguring the address Reminder of the various connection methodsConfiguring communication monitoring PLC configuration and applicationAddress ATV38 switches ATV61 switches 12345678 Reminder of possible connection methodsCommunication via CANopen network Configuring polarity on the drive RS 485 busPLC configuration and application Matching the line termination resistorConfiguring the drive Address and Baud rateAddress Configuring the drive address on the Profibus DP networkCommunication via Profibus DP network 1234Configuring the drive in ATV38 Interchangeability mode Communication faultCommunication via Fipio network VW3 A3 311 option card Connecting to the Fipio busConfiguring the drive address on the Fipio network PresentationFamily Altivar 38 PKW indexed periodic variablesManaging loss of Fipio communication Base moduleConfiguring the communication parameters Communication via Interbus networkConfiguring the drive address on the Modbus Plus network Communication via Modbus Plus networkATV38 ATV61 Communication fault Communication via DeviceNet network Configuring the drive on the networkConfiguring the drive address on the DeviceNet network MACPLC configuration and application Drive implementation on the DeviceNet network Implementation of the communication option cards Implementation of the communication option cards Implementation of the communication option cards Implementation of the communication option cards P06 P06 Communication fault Communication via Ethernet network Drive configuration in Expert modeUsing the Bootp protocol Transmission speedActivating the service Using the DHCP-FDR protocolFaulty Device Replacement FDR Procedure on the AltivarAvailable address fields Modbus serviceProgramming the Altivar 38 Ethernet parameters XxxxConfiguring the periodic parameter assignment table IO Scanning serviceEthernet card access to the Modbus server Modbus functions availableFDR service fault EPF2 Configuring the IO Scanner page from the Http server Implementation of the communication option cards Snmp agent Configuring the IO Scanner page using TCP/Modbus messagingAltivar 38 PKW parameter-setting service Description ATV61 registerFDR service fault EPF2 PDA Altivar page Last Fault = ILF FaultCommunication fault Standard Http serverAS-i Speed mode, 1 direction of operation 11 . +/- speed modeAssignment of the Inputs/Outputs Assignment of inputs/outputsManaging the terminal outputs AS-i monitoring bits Configuring the drive logic I/OSpeed mode, 2 directions of operation LimitationsMulti-motor card Application-specific option cardsPump card Multi-parameter cardAtv61migrationenv1 2006-04