Husqvarna TS 355 Check Before Operating, Fitting The Blade Figure, Operating Instructions

Page 18

3 Check Before Operating

All Models:

Take into account the working conditions from a health and safety point of view.

For start up refer to the engine or motor manual.

Electric Models Only:

Make sure that the extension cord length is properly sized for the motor used on this saw. See the chart in Section 2 of this document.

WARNING: Make sure the unit is connected to a properly grounded outlet. Failure to comply with this warning could result in serious bodily injury or death!

Gasoline Model Only:

Fuel: Check the engine operation manual. Unleaded gasoline is recommended.

Oil: Lock the Head Platform Assembly (B) with the engine in a horizontal position, then, check that the engine oil level is correct. Check the oil level frequently to ensure that the level never falls below that specified in the engine operation manual. If the oil level is low, add SAE 10W30, service classification SF or SG oil (for normal conditions) as recommended in the engine operation manual. DO NOT overfill engine with oil!

4 Fitting The Blade (Figure 7)

All Models:

The blade rotates in a “down-cut” direction. This means that the front of the blade is moving downward while the rear of the blade is moving upward. Mount the. Diamond Blade (DD) so that the arrow on the blade. rotates in this “down-cut” direction. The Diamond Blade (DD) can be installed / removed by using the 3/4". (19 mm) end of the Wrench (LL) provided (Fig. 4).

After mounting the blade, it should align over the top of the wooden insert in the Conveyor Cart (C). If this is not true, loosen the setscrews that secure the Bear- ings (H) to the Head Platform Assembly (B) (Fig. 3).. Position the Head Platform Assembly (B) to the left or right until the Diamond Blade (DD) is aligned over the top of the wooden insert, then re-tighten the Bearing (H) setscrews. During operation of this unit, the blade can, and should, pass into the wooden insert, but NOT into the cast aluminum part of the Conveyor Cart (C).

WARNING: Conventional “Wet” diamond blades MUST be used with water. DO NOT use conventional “Wet” diamond blades without water. Using conventional “wet” diamond blades without water can result in injury or death of the operator or persons in the work area!

Warning: Use only Abrasive blades of a reinforced type.

Electric Models Only:

Mount the Diamond Blade (DD):

1.Using the Wrench (LL) provided (or one of your own) loosen the Capscrew (BB) by turning it Counter- Clockwise (Electric Models Only).

CAUTION: Note that on Electric Models the Capscrew (BB) has RIGHT HAND THREADS. Installation of the wrong capscrew could damage the blade shaft!

2.Remove the outer Flange (CC) and make sure the outer Flange (CC), the Inner Flange (Not Shown), and arbor shaft (Not Shown) are clean and not. damaged.

3.Mount the Diamond Blade (DD) to the arbor and. install the outer Flange (CC). Install and tighten Capscrew (BB) by turning it in a Clockwise. direction (Right Hand Thread). Use the Wrench

(LL)to firmly tighten the Capscrew (BB) to the arbor shaft.

Gasoline Model Only:

Always set the Engine Key Switch (VV) to the "OFF" position BEFORE mounting the blade

Mount the Diamond Blade (DD):

1.Using the Wrench (LL) provided (or one of your own) loosen the Capscrew (BB) by turning it Clockwise. (Gasoline Model Only).

CAUTION: Note that on Gasoline Models the Capscrew (BB) has LEFT HAND THREADS. Installation of the wrong capscrew could damage the blade shaft!

2.Remove the outer Flange (CC) and make sure the outer Flange (CC), the Inner Flange (Not Shown), and arbor shaft (Not Shown) are clean and not. damaged.

3.Mount the Diamond Blade (DD) to the arbor and install the outer Flange (CC). Install and tighten the Capscrew (BB) by turning it in a Counter-Clockwise direction (Left Hand Thread). Use the Wrench (LL) to firmly tighten the Capscrew (BB) to the arbor shaft.

5 Operating Instructions

All Models: (See Figures 5 & 6)

Configure the saw for the type of operation required, wet or dry. Note that the saw is factory assembled for wet operation.

18

Image 18
Contents TS 355 G Esta máquina hayan leído este manual Symbol Definitions Definición DE Simbolos Page Page Hearing Hazard Riesgo DE Daño AuditivoCalifornia Prop 65 Warning 542 19 Location Front of Pan, Belt Guard, All Models Qty Specifications Power SourceSAW Dimensions Do only cut in a straight line Do use caution when handling fuelBlade Follow all electrical codes in your areaDo not Figures Page Parts Identification Service Every 50 Hours With Machine Cold and Setting LevelService Daily Hour Operation Check ListFeatures AssemblyIndication Mandatory Information Instruction Electric Models FIG Extension Cord Size A.W.G. MinimumGasoline Model Fig Check Before Operating Fitting The Blade FigureOperating Instructions Cutting Operations Maintenance Incidents During OperationImportant Advice Belt TensionAll Models Figs Spare Parts AccessoriesRepairs Reference InformationNota Especificaciones Modelo no Dimensiones DE LA Sierra Advertencias Advertencias FigurAS Page Identificación de Piezas CON LA Maquina Fria Y Nivelada Mantenimiento DiarioMantenimiento Cada 50 Horas Caracteristicas ArmadoDel Motor Enchutes y Connectores del Motor Electrico ConectorMotor Requenido Nema NoTodos los Modelos Verifique Antes De OperarColocación De La Hoja Ver la Ilustracion Solamente Modelos EléctricosInstrucciones De Operación Advertencia Use solamente hojas abrasivas del tipo reforzadoIncidentes Durante La Operación Procedimiento para el Cambio de Aceite del Motor MantenimientoVerifique Diariamente Todos los Modelos Alineación de la Hoja Ilustraciones 11 yTensión de la Cinta en Consejo ImportanteAccesorios ReparacionesPiezas De Repuesto NotasPage Page Wiring Diagram 3 HP Electric Motor Wiring Diagram 5.5 HP Honda Nota Nota Nota Canada Corporate OfficeSouth Carolina International542 20