Husqvarna FS 6600 D, FSA 8400 D 1I. Voltage Gauge Shows the voltage of the electrical system

Page 46

FIGURE 1

1A. KNOB: Use to tighten operator grip handles.

1B. HANDLE BARS: For operator gripping.

1C. HOUR METER: Records engine hours of operation.

1D. FUEL TANK FILL: Fill the fuel tank at this location.

1E. WATER TEMPERATURE GAUGE: Water/Glycol is the coolant. Monitors the engine coolant temperature. Maximum Safe temperature is 220°F.

1F. ENGINE THROTTLE: Controls Engine RPM. Push Red Button to unlock. Push in to decrease RPM. Pull out to increase RPM. Or Turn Clockwise to increase RPM. Turn counterclockwise to decrease RPM.

1G. ENGINE TACHOMETER: Shows the engine RPM’s and hours.

1H. ENGINE START SWITCH: Start and stop the engine using this switch. Also preheats the engine

1I. VOLTAGE GAUGE: Shows the voltage of the electrical system.

1J. AXLE ADJUSTMENT SWITCH: Toggle switch to adjust rear drive axle. Push switch right to make saw drive to the right. Left to make saw drive to the left.

1K. RED PALM SWITCH: For EMERGENCY STOP of the saw. Stops all systems except lights, pull OUT to reset. Do not use for routine stopping.

1L. WATER SAFETY SWITCH: Stops the engine if the water supply to the blade is interrupted. Set to activate switch.

1M. BLADE DEPTH STOP: Activates or overrides the depth stop for repetitive cuts at the same depth.

1N. AIR RESTRICTION INDICATOR: Service air filter elements when indicator shows a red mark. Reset before starting engine.

1O. SPEED CONTROL LEVER: Controls forward and reverse directions, stop, and the speed of the saw.

1P. RAISE/LOWER SWITCH: Located on speed control lever. Use to raise and lower the saw. Push up to raise saw upward. Push down to lower the saw.

1Q. BLADE DEPTH INDICATOR: Displays cutting depth. Sets cutting depth for BLADE DEPTH STOP.

1R. HANDLE ADJUSTMENT LOCK: Turn Clockwise to lock handle bar in position. Turn Counterclockwise to unlock and reposition handlebar.

1S. WATER INLET: Connects to 3/4” garden hose for fresh water supply.

1T. WATER VALVE: Controls water flow rate to cool the blade.

1U. SAW LOWERING SPEED CONTROL KNOB: Turn knob clockwise to slow lowering speed. Turn knob counterclockwise to increase lowering speed.

1V. BLADE CLUTCH SWITCH: Engages Blades Drive. Light indicates Clutch Engaged. Engage only with engine RPM at 1200 RPM or less

1W. OIL PRESSURE LIGHT: Lights up when engine oil pressure is low and when key is on with the engine off.

1X. FUEL LEVEL SIGHT GAUGE: Shows the level of fuel in the fuel tank.

1Y. RADIATOR COOLANT OVERFLOW BOTTLE: Recovers radiator coolant when engine is hot. Should be 1/4 full when engine is off and cool.

1Z. TACHOMETER SELECT SWITCH: Can be set to indicate either engine speed (RPM, n/min), or blade shaft speed (RPM, n/min). Set to upper position to indicate engine speed, lower position to indicate blade shaft speed. Standard equipment on machines equipped with three-speed gearbox, optional for all others.

WARNING: Take Notice of TACHOMETER SELECT SWITCH (1Z) position! Tachometer can indicate Blade Speed or Engine Speed. Serious injury can occur to the operator or people in the work area if the rotational speed (n/min) of the DIAMOND BLADE (2E) exceeds the maximum speed (n/min) marked on the DIAMOND BLADE (2E).

46

Page 45 Page 47
Image 46
Page 45 Page 47
Contents Operator’s manual FS 6600 D 3-Speed Model Eff. S/NDéclaration DE Conformité À LA Directive « Machines » Manufacturer El FabricanteNotas Remarque Table of Contents ÍNDICE DE PáginaTable des matières Notas Remarque Safety First BladeDo not USAAdvertencias Advertencias Faire Usure inhabituelle, NE PAS Utiliser LE DisqueNE PAS Faire Page Page Page Page Page Page Page Page Poison Exhaust GAS General InformationDust Warning California Prop 65 WarningTechnical Data Sound Level, EMC, and HAV Sound LevelPeligro Para LA AUDICIóN AdvertenciaInformación general Advertencia Relativa AL Polvo Advertencia de la Proposición 65 del Estado de CaliforniaDatos técnicos Nivel sonoro, EMC y HAV Nivel sonoroAvertissement Information généraleAvertissement Relatif À LA Poussière Proposition 65 de Californie AvertissementDonnées techniques niveau sonore, CEM et VMB Niveau sonoreGearbox Range / Blade RPM Gearbox Range / Blade RPMOperating Instructions Depth INDICATOR, TOPBlade Rotation Direction Depth Indicator THROTTLE, DieselTachometer / Blade RPM-4.5 Flange Transmission Bypass ValveHusqvarna Crown H Decal Tachometer / Blade RPM-5.0 FlangeMuffler HOT Manual Axle AdjustmentBlade Guard Warning TOP of Blade Guard Front Side of Muffler Brace Right Side Top of Fan ShieldSound Level CE Radiator Filter Rear CowlingPatents TOP of Blade Guard 542 19FS6600 Diesel Specifications Max. Horsepower Weight lb. Kg UncratedEngine Specifications Displacement cu. in. lEspecificaciones DE Diesel FS6600 Especificaciones DE Diesel FS8400 Spécifications DU FS6600 Diesel Spécifications DU FS8400 Diesel Instrucciones Especiales Special InstructionsInstructions Spéciales 2170 Información DEL Motor Service Every 100 Hours Service DailyService Every 50 Hours Service Every 250 Hours1I. Voltage Gauge Shows the voltage of the electrical system 1M. V-BELTS Set 1DD. Radiator AIR Filter Element2C. Outer Flange Arbor Use to support the diamond blade 1N. Gearbox Pulley2M. V-BELTS Set 2N. Gearbox Pulley5A. AIR Filter Assembly Includes 5F. Fuel Filter Water Separator See JohnHydrostatic Transmission Pump Do not Operate Engine with Shields RemovedMoving The Machine UsesIndication Mandatory Information Instruction Check Before Starting Transport Blade RemovedFitting The Blade See Figures 1, 2 Using the Blade Depth Indicator 1QStarting The Saw Blade Cutting Depth InformationIncidents During Sawing Stopping The SawSee Figures Adjustments Straight Line Sawing MaintenanceHydraulic System Important AdviceBlade Shaft V-Belt Tension Fuel FilterBlade Shaft Speed Engine / Blade Shaft / Gearbox Speed AdjustmentEngine Speed Single Speed Gearbox ModelLarge Diameter Models AccessoriesWeight Kits Blade Guard Conversion KitsRepairs Spare PartsLista DE Comprobación Preliminar Figura 1Z. Interruptor Selector DEL Tacómetro 1AA. Colgador Para Manguera Sujeta la1N. Polea DE LA Caja DE Engranajes 1A. Caja DE Engranajes DEL Motor Modelo1M. Correas Trapezoidales Juego de 2A. Caja DE Engranajes DEL Motor Modelo2M. Correas Trapezoidales Juego de 2N. Polea DE LA Caja DE Engranajes5A. Conjunto DEL Filtro DE Aire Incluye 5N. Bomba DE Transmisión HidrostáticaUsos Traslado de la máquinaRevisiones antes del arranque Transporte sin la hojaColocación de la hoja Información sobre la profundidad de corte de la hoja Arranque de la sierraVea las figuras 1, 2 y Uso del Indicador DE Profundidad DE LA Hoja 1QParada de la sierra Ajustes Corte en línea recta Incidentes durante el corte con sierraMantenimiento Sistema DE Enfriamiento Tensión de la correa trapezoidal del eje de la hojaSistema hidráulico Filtro DE AireVelocidad DEL Motor Consejo importanteVea las figuras 2 y Velocidad DEL EJE DE LA Hoja127 mm 152 mm114,3 mm Reparaciones AccesoriosModelos de diámetro grande Piezas de repuestoListe DE Vérifications Avant Utilisation Guide Rapide DU Calendrier D’ENTRETIEN1L. Interrupteur DE Sécurité DE L’EAU 1O. Levier DE Commande DE Vitesse1J. Commutateur DE Réglage D’ESSIEU 1P. Commutateur DE RELEVAGE/ABAISSEMENT1X. Jauge Visuelle DU Niveau DE Carburant 1DD. Élément DE Filtre À AIR DU Radiateur1F. Écran Protecteur DE Courroie Les 1A. Boîte DE Transmission DU Moteur Modèle2F. Écran Protecteur DE Courroie Les 2M. Courroies Trapézoïdales Jeu de 2N. Poulie DE Boîte DE Transmission5N. Pompe DE Transmission Hydrostatique 5A. Ensemble DU Filtre À AIR Comprend6H. Filtre À Huile Moteur L’élément du filtre Déplacement de la machine UtilisationsVérifier avant de démarrer Transport disque retiréMise en place du disque Marche Démarrage de la scieVoir les figures 1, 2 et Information sur la profondeur de sciage du disquePage Réglages Sciage en ligne droite Arrêt de la scieIncidents pouvant se produire durant le sciage EntretienTension des courroies trapézoïdales de l’axe du disque Disque EN Diamant Régime Moteur Circuit hydrauliqueConseil important Vitesse DE L’AXE DU DisquePage Kits DE Conversion DES Protections DE Disque Accessoires16 Modèles de grand diamètre Kits DE Masses D’ALOURDISSEMENT17 Réparations 18 Pièces détachéesNotas Notes Size To Convert Size To Convert ToFrom 900mm 1000mm FS8400 Diesel Blade Size Conversion Chart 1000mm 1200mm 1500mm 350 mm / 450 mm Tamaño para convertir aTamaño Pulgadas / 18 pulgadas 750 mm1000 mm Tamaño para Pulgadas Convertir de450 mm Tamaño 450 mm 650 mm 750 mm 900 mmFS8400 Diesel Tabla DE Conversiones DE Tamaños DE LA Hoja 36 po Taille à laquelle convertirTaille 14 po 18 po 26 po 30 po ’origine 42 poTaille 36 po 42 po ’origine 48 po Taille à laquelle converterTaille 18 po 26 po 30 po 36 po ’origine 60 poTaille 42 po 48 po 60 po ’origine 900mm14-26 18-30 20-36 26-42 FS 6600 DFS 8400 D 106 107 Schéma 3 Schéma de câblage Câblage du capot FS6600-FS8400 109 Component Designators for PRO 66/ PRO 111 504 63
Related manuals
Manual 98 pages 44.65 Kb

FSA 8400 D, FS 6600 D specifications

Husqvarna has long been a trusted name in the world of professional outdoor power equipment, and its FS 6600 D and FSA 8400 D models exemplify the company's commitment to quality and performance.

The Husqvarna FS 6600 D is a powerful walk-behind concrete saw that is renowned for its exceptional cutting efficiency and robust design. Powered by a high-torque diesel engine, the FS 6600 D is engineered to handle tough, heavy-duty applications with ease. One of its standout features is its adjustable, heavy-duty frame that can accommodate various blade sizes, making it versatile for different cutting depths and applications. The saw's integrated water system helps to manage dust and keeps the blade cool during operation, resulting in cleaner cuts and prolonging blade life. Furthermore, the intelligent design of the FS 6600 D includes an easy-to-use control panel, ensuring operators can quickly start and adjust the saw without hassle.

On the other hand, the Husqvarna FSA 8400 D is part of Husqvarna’s range of professional grass trimmers, specifically designed for demanding tasks and prolonged use. Its lightweight yet robust design makes it an ideal choice for professionals who require mobility and efficiency. The FSA 8400 D features a high-capacity battery and an efficient brushless motor, ensuring powerful performance with minimal noise and vibration. The trimmer’s adjustable handle and ergonomic design allow users to maneuver easily, reducing fatigue during extended usage.

Both products also incorporate advanced technologies to enhance user experience. For instance, the FS 6600 D employs Husqvarna’s SmartStart technology, allowing for easier and faster starts. Similarly, the FSA 8400 D utilizes an intuitive control system that seamlessly integrates speed and power settings, optimizing performance based on the demands of the task at hand.

In summary, the Husqvarna FS 6600 D and FSA 8400 D are prime examples of innovative engineering combined with user-focused design. Their robust features, advanced technologies, and unmatched performance make them essential tools for professionals looking to excel in their trade. Whether cutting concrete or tidying up grassy areas, Husqvarna proves that it understands the needs of its users, delivering reliable solutions that stand the test of time.
Top Page Image Contents