Husqvarna FS 6600 D, FSA 8400 D Transport Blade Removed, Check Before Starting, Fitting The Blade

Page 52

•Turn the Engine Start Switch (1H) to the “2” (START) position until the engine starts,

then release the switch. It will return to RUN position. If the engine does not start, repeat these steps.

•Push the Speed Control Lever (1O) forward for FORWARD saw movement, or to the rear for REVERSE saw movement. The further you push the lever the faster the speed.

DO NOT OPEN the bypass valve (5M) to neutral while the saw is parked on a grade (or hill), The Operator will lose control and injury or damage could occur.

3 Transport (Blade Removed)

(See Figures 1, 2, and 5)

Turn engine off. Set Speed Control Lever (1O) to STOP (1BB) position. Remove diamond

blade (2E) before transport.

When moving the saw up and down ramps, with engine on, use extreme caution.

•To go DOWN a ramp drive the saw FORWARD slowly.

•To go UP a ramp, back the saw in REVERSE slowly.

For steep ramps, always use a winch. Never stand below the machine.

Lifting The Saw. The saw can only be lifted by the factory installed Lifting Bail (6A).

To Transport By Vehicle:

•Set the Engine Start Switch (1H) in the OFF position.

•Set Speed Control Lever (1O) in the STOP (1BB) position.

•Push Handle Bars (1B) inward and tighten Knobs (1A).

Block the saw in place or secure it into place using the factory installed TIE DOWN LUGS (3H), front and rear to prevent movement

during transport.

4 Check Before Starting

Take into account the working conditions from health and safety point of view.

•Fuel (Check the engine maintenance manual.) Use No. 2 Diesel Fuel for normal conditions.

•Check that the engine oil level is correct. Because the engine often operates at an angle, check the oil level

(with engine horizontal) frequently to ensure that the oil level never falls below the lower mark on the dipstick. 15W40 CD or CE engine oil is recommended. (6B)

•For start up, refer to the engine manual. See John Deere Manual OMRG34851

5 Fitting The Blade

(See Figures 1 and 2)

•Set engine Start Switch (1H) to “1” position.

•Raise Machine to a high position using the raise/ lower switch (1P) on the Speed Control Lever (1O)

•Set the Engine Start Switch (1H) to the “0” (OFF) position.

•Loosen Bolt on Blade Guard Latch (2G).

•Raise Front Half of Blade Guard (2H)

•Loosen Bladeshaft Bolt (2A) Remove Outer Flange (2B).

•Fit Diamond Blade (2E) to Outer Flange Arbor (2C).

•Install Outer Flange (2B) into the Blade Shaft (2I) making sure that the Locking Pin (2D) passes through the Diamond Blade (2E) and into the Inner Flange (2F).

Note the direction of rotation of the blade. The direction of rotation is shown by an arrow on both the DIAMOND BLADE (2E) and the BLADE GUARD (2H). Make sure that the contact surfaces on the DIAMOND BLADE (2E), INNER & OUTER FLANGES (2B & 2F) and BLADE ARBOR (2C) are clean.

•Rotate Outer Flange (2B) and Diamond Blade (2E) in the opposite direction of blade rotation to remove backlash.

•Install and tighten Blade Shaft Bolt (2A) using the

Blade Shaft Wrench while firmly holding the Diamond

Blade (2E).

•Lower front half of Blade Guard (2H) and tighten the Bolt (2G) on the Blade Guard Latch (2G).

The Blade Shaft Bolt (2A) on the Right Hand side has Left Hand threads. The Blade Shaft Bolt (2A) on the Left Hand side has Right Hand threads.

Slip on blade guards are provided with a safety latch which engages the support spade and a bolt to retain the rear of the guard.

Do not operate this saw without the latch engaged and the bolt installed. Inspect blade guards and latches frequently. Do not use if damaged.

52

Page 51 Page 53
Image 52
Page 51 Page 53
Contents Operator’s manual FS 6600 D 3-Speed Model Eff. S/NDéclaration DE Conformité À LA Directive « Machines » Manufacturer El FabricanteNotas Remarque Table of Contents ÍNDICE DE PáginaTable des matières Notas Remarque Safety First BladeDo not USAAdvertencias Advertencias Faire Usure inhabituelle, NE PAS Utiliser LE DisqueNE PAS Faire Page Page Page Page Page Page Page Page Poison Exhaust GAS General InformationDust Warning California Prop 65 WarningTechnical Data Sound Level, EMC, and HAV Sound LevelPeligro Para LA AUDICIóN AdvertenciaInformación general Advertencia Relativa AL Polvo Advertencia de la Proposición 65 del Estado de CaliforniaDatos técnicos Nivel sonoro, EMC y HAV Nivel sonoroAvertissement Information généraleAvertissement Relatif À LA Poussière Proposition 65 de Californie AvertissementDonnées techniques niveau sonore, CEM et VMB Niveau sonoreGearbox Range / Blade RPM Gearbox Range / Blade RPMDepth INDICATOR, TOP Blade Rotation Direction Depth IndicatorOperating Instructions THROTTLE, DieselTransmission Bypass Valve Husqvarna Crown H DecalTachometer / Blade RPM-4.5 Flange Tachometer / Blade RPM-5.0 FlangeManual Axle Adjustment Blade Guard Warning TOP of Blade GuardMuffler HOT Front Side of Muffler Brace Right Side Top of Fan ShieldRadiator Filter Rear Cowling PatentsSound Level CE TOP of Blade Guard 542 19FS6600 Diesel Specifications Weight lb. Kg Uncrated Engine SpecificationsMax. Horsepower Displacement cu. in. lEspecificaciones DE Diesel FS6600 Especificaciones DE Diesel FS8400 Spécifications DU FS6600 Diesel Spécifications DU FS8400 Diesel Instrucciones Especiales Special InstructionsInstructions Spéciales 2170 Información DEL Motor Service Daily Service Every 50 HoursService Every 100 Hours Service Every 250 Hours1I. Voltage Gauge Shows the voltage of the electrical system 1DD. Radiator AIR Filter Element 2C. Outer Flange Arbor Use to support the diamond blade1M. V-BELTS Set 1N. Gearbox Pulley2M. V-BELTS Set 2N. Gearbox Pulley5A. AIR Filter Assembly Includes 5F. Fuel Filter Water Separator See JohnHydrostatic Transmission Pump Do not Operate Engine with Shields RemovedMoving The Machine UsesIndication Mandatory Information Instruction Check Before Starting Transport Blade RemovedFitting The Blade Using the Blade Depth Indicator 1Q Starting The SawSee Figures 1, 2 Blade Cutting Depth InformationIncidents During Sawing Stopping The SawSee Figures Adjustments Straight Line Sawing MaintenanceImportant Advice Blade Shaft V-Belt TensionHydraulic System Fuel FilterEngine / Blade Shaft / Gearbox Speed Adjustment Engine SpeedBlade Shaft Speed Single Speed Gearbox ModelAccessories Weight KitsLarge Diameter Models Blade Guard Conversion KitsRepairs Spare PartsLista DE Comprobación Preliminar Figura 1Z. Interruptor Selector DEL Tacómetro 1AA. Colgador Para Manguera Sujeta la1A. Caja DE Engranajes DEL Motor Modelo 1M. Correas Trapezoidales Juego de1N. Polea DE LA Caja DE Engranajes 2A. Caja DE Engranajes DEL Motor Modelo2M. Correas Trapezoidales Juego de 2N. Polea DE LA Caja DE Engranajes5A. Conjunto DEL Filtro DE Aire Incluye 5N. Bomba DE Transmisión HidrostáticaUsos Traslado de la máquinaRevisiones antes del arranque Transporte sin la hojaColocación de la hoja Arranque de la sierra Vea las figuras 1, 2 yInformación sobre la profundidad de corte de la hoja Uso del Indicador DE Profundidad DE LA Hoja 1QParada de la sierra Ajustes Corte en línea recta Incidentes durante el corte con sierraMantenimiento Tensión de la correa trapezoidal del eje de la hoja Sistema hidráulicoSistema DE Enfriamiento Filtro DE AireConsejo importante Vea las figuras 2 yVelocidad DEL Motor Velocidad DEL EJE DE LA Hoja127 mm 152 mm114,3 mm Accesorios Modelos de diámetro grandeReparaciones Piezas de repuestoListe DE Vérifications Avant Utilisation Guide Rapide DU Calendrier D’ENTRETIEN1O. Levier DE Commande DE Vitesse 1J. Commutateur DE Réglage D’ESSIEU1L. Interrupteur DE Sécurité DE L’EAU 1P. Commutateur DE RELEVAGE/ABAISSEMENT1X. Jauge Visuelle DU Niveau DE Carburant 1DD. Élément DE Filtre À AIR DU Radiateur1F. Écran Protecteur DE Courroie Les 1A. Boîte DE Transmission DU Moteur Modèle2F. Écran Protecteur DE Courroie Les 2M. Courroies Trapézoïdales Jeu de 2N. Poulie DE Boîte DE Transmission5N. Pompe DE Transmission Hydrostatique 5A. Ensemble DU Filtre À AIR Comprend6H. Filtre À Huile Moteur L’élément du filtre Déplacement de la machine UtilisationsVérifier avant de démarrer Transport disque retiréMise en place du disque Démarrage de la scie Voir les figures 1, 2 etMarche Information sur la profondeur de sciage du disquePage Arrêt de la scie Incidents pouvant se produire durant le sciageRéglages Sciage en ligne droite EntretienTension des courroies trapézoïdales de l’axe du disque Circuit hydraulique Conseil importantDisque EN Diamant Régime Moteur Vitesse DE L’AXE DU DisquePage Accessoires 16 Modèles de grand diamètreKits DE Conversion DES Protections DE Disque Kits DE Masses D’ALOURDISSEMENT17 Réparations 18 Pièces détachéesNotas Notes Size To Convert Size To Convert ToFrom 900mm 1000mm FS8400 Diesel Blade Size Conversion Chart 1000mm 1200mm 1500mm Tamaño para convertir a Tamaño Pulgadas / 18 pulgadas350 mm / 450 mm 750 mm1000 mm Tamaño para Pulgadas Convertir de450 mm Tamaño 450 mm 650 mm 750 mm 900 mmFS8400 Diesel Tabla DE Conversiones DE Tamaños DE LA Hoja Taille à laquelle convertir Taille 14 po 18 po 26 po 30 po ’origine36 po 42 poTaille 36 po 42 po ’origine Taille à laquelle converter Taille 18 po 26 po 30 po 36 po ’origine48 po 60 poTaille 42 po 48 po 60 po ’origine 900mm14-26 18-30 20-36 26-42 FS 6600 DFS 8400 D 106 107 Schéma 3 Schéma de câblage Câblage du capot FS6600-FS8400 109 Component Designators for PRO 66/ PRO 111 504 63
Related manuals
Manual 98 pages 44.65 Kb

FSA 8400 D, FS 6600 D specifications

Husqvarna has long been a trusted name in the world of professional outdoor power equipment, and its FS 6600 D and FSA 8400 D models exemplify the company's commitment to quality and performance.

The Husqvarna FS 6600 D is a powerful walk-behind concrete saw that is renowned for its exceptional cutting efficiency and robust design. Powered by a high-torque diesel engine, the FS 6600 D is engineered to handle tough, heavy-duty applications with ease. One of its standout features is its adjustable, heavy-duty frame that can accommodate various blade sizes, making it versatile for different cutting depths and applications. The saw's integrated water system helps to manage dust and keeps the blade cool during operation, resulting in cleaner cuts and prolonging blade life. Furthermore, the intelligent design of the FS 6600 D includes an easy-to-use control panel, ensuring operators can quickly start and adjust the saw without hassle.

On the other hand, the Husqvarna FSA 8400 D is part of Husqvarna’s range of professional grass trimmers, specifically designed for demanding tasks and prolonged use. Its lightweight yet robust design makes it an ideal choice for professionals who require mobility and efficiency. The FSA 8400 D features a high-capacity battery and an efficient brushless motor, ensuring powerful performance with minimal noise and vibration. The trimmer’s adjustable handle and ergonomic design allow users to maneuver easily, reducing fatigue during extended usage.

Both products also incorporate advanced technologies to enhance user experience. For instance, the FS 6600 D employs Husqvarna’s SmartStart technology, allowing for easier and faster starts. Similarly, the FSA 8400 D utilizes an intuitive control system that seamlessly integrates speed and power settings, optimizing performance based on the demands of the task at hand.

In summary, the Husqvarna FS 6600 D and FSA 8400 D are prime examples of innovative engineering combined with user-focused design. Their robust features, advanced technologies, and unmatched performance make them essential tools for professionals looking to excel in their trade. Whether cutting concrete or tidying up grassy areas, Husqvarna proves that it understands the needs of its users, delivering reliable solutions that stand the test of time.
Top Page Image Contents