Southbend SB1019 owner manual ElectricalL CTRICALSafety Instructions, Wiring Diagram Color KEY

Page 43

For Machines Mfg. Since 8/09

E L E C T R I C A L

Model SB1019

ElectricalL CTRICALSafety Instructions

These pages are accurate at the time of printing. In the constant effort to improve, however, we may make changes to the electrical systems of future machines. Study this section carefully. If you see differences between your machine and what is shown in this section, call Technical Support at (360) 734-1540 for assistance BEFORE making any changes to the wiring on your machine.

1.Shock Hazard: It is extremely dangerous to perform electrical or wiring tasks while the machine is connected to the power source. Touching electrified parts will result in personal injury including but not limited to severe burns, electrocution, or death. For your own safety, disconnect machine from the power source before servicing electrical components or performing any wiring tasks!

2.Wire Connections: All connections must be tight to prevent wires from loosening during machine operation. Double-check all wires disconnected or connected during any wiring task to ensure tight connections.

3.Modifications: Using aftermarket parts or modifying the wiring beyond what is shown in the diagram may lead to unpredictable results, including serious injury or fire.

4.Motor Wiring: The motor wiring shown in these diagrams is current at the time of printing, but it may not match your machine. Always use the wiring diagram inside the

5.Circuit Requirements: Connecting the machine to an improperly sized circuit will greatly increase the risk of fire. To minimize this risk, only connect the machine to a power circuit that meets the minimum requirements given in this manual.

6.Capacitors/Inverters: Some capacitors and power inverters store an electrical charge for up to 10 minutes after being disconnected from the power source. To reduce the risk of being shocked, wait at least this long before working on capacitors.

7.Wire/Component Damage: Damaged wires or components increase the risk of serious personal injury, fire, or machine damage. If you notice that any wires or components are damaged while performing a wiring task, replace those wires or components before completing the task.

8.Experiencing Difficulties: If you are experiencing difficulties understanding the information included in this section, contact

WIRING DIAGRAM COLOR KEY

BLACK

BLUE

BROWN

NOTICE:

BLUE

RED

PINK

WHITE

WHITE

LIGHT

 

YELLOW

GREEN

PURPLE

BLUE

GREEN

 

TUR-

GRAY

ORANGE

YELLOW

QUIOSE

 

 

 

The photos and diagrams included in this section are best viewed in color. You can see them in color at www.southbendlathe.com.

-41-

Image 43
Contents METAL-CUTTING Bandsaw Manual Feedback UpdatesCustomer Service Scope of ManualTable of Contents About This Machine FeaturesCapabilities ON/OFF IdentificationMachine Specifications Machine SpecificationsOther Understanding Risks of Machinery Basic Machine SafetyF E T Y Additional Metal Bandsaw Safety Full-Load Current Rating Power Supply RequirementsThings Youll Need AvailabilityGrounding Requirements For 110V Connection PrewiredCircuit Information Circuit Requirements forInventory UnpackingExtension Cords Before cleaning, gather the following Cleaning & ProtectingBasic steps for removing rust preventative Location Leveling & Mounting Lifting & MovingLeveling Machine Mounts Bolting to Concrete FloorsTo set up the machine Machine SetupInstalling stop rod Power ConnectionTest Run Inspections AdjustmentsTo test run your machine OperationPERATIONOverview Description of Controls & Components Blade Width Blade SelectionBlade Terminology Blade LengthTooth Type Tooth SetTo select the correct blade pitch Blade Pitch TPITo change the blade Blade ChangesMost common causes of avoidable blade breakage are Blade TensionBlade Breakage To tension the blade on the bandsawBlade Break-In Blade Care & Break-InBlade Speed Blade CareChip Inspection Chart Blade Speed ChartDownfeed Pressure Downfeed RateCuts to the Right Angle CutsCuts to the Left Vise Quick Release To adjust the blade guideBlade Guide Workpiece HoldingCutting Fluid System Cutting FluidTo use the cutting fluid system Coolant control valve Operation TipsLubrication CleaningGearbox Machine StorageTroubleshooti NG Blade Selection section beginning on Troubleshooti NG Blade Tracking To adjust the blade trackingSquaring the Blade Blade Guide BearingsTo adjust the angle stops Adjusting Angle StopsWiring Diagram Color KEY ElectricalL CTRICALSafety InstructionsTo convert the Model SB1019 to 220V Conversion110 VAC Wiring DiagramLimit switch and coolant pump locations Wiring Component LocationsCabinet & Base Description Cabinet & Base Parts ListMotor & Head Motor & Head Parts List Coolant Nozzle Bracket Blade Guide AssembliesGearbox Gearbox Parts List Machine Labels R R a N T Y Southbendlathe.com