Connecting Power Cord to Lathe

EVS Toolroom Lathes

P R E P A R A T I O N

For Machines Mfg. Since 7/09

Electrocution or death will occur if you attempt this procedure with the power cord connected to the power source. The cord must be disconnected from power before performing this procedure.

These instructions are for setups where the lathe will be connected to the power source with a power cord and plug, as opposed to a hardwire setup.

To connect power cord to the lathe:

1.Unlock and open the main electrical cabinet door, and install a strain relief in the location shown in Figure 14.

	Incoming
	Power	Main
	Strain
		Power
	Relief
		Switch

Figure 14. Location to connect power inside main

electrical cabinet.

2.Thread the power cord through the strain relief, and up to the main power switch shown in Figure 14.

3.Connect the incoming L1, L2, L3 and ground wires to the main power switch terminals, as illustrated in Figure 15.

To Power Source
	Rdd	Wt
	Bk	Gn
L1	L2	Gn
L1	L2	L3
5	3	1	Ground
5	3	1
MASTER
POWER SWITCH
4	6	2	Power
			Connection
L1	L2	L3	Terminals

Figure 15. Power connection at main power switch.

4.Make sure the cord/wires have loose slack between the strain relief and terminal connections, then tighten the strain relief to secure the power cord.

Note: The strain relief must be tightened against the outermost jacket of the cord. Avoid over- tightening the strain relief or it may crush the cord and cause a short.

5.Test the strain relief to ensure it is properly tightened by pulling the cord from outside the box with light-to-moderate force. When the strain relief is properly tightened, the cord will not slide.

6.Close and lock the main electrical box door.

Hardwiring Lathe to Power Source

Hardwire setups require power supply lines to be enclosed inside of conduit, which is securely mounted and constructed in adherence to applicable electrical codes.

A hardwire setup for this machine must be equipped with a locking disconnect switch as a means to disconnect the power during adjustments or maintenance, which is a typical requirement for lock-out/tag-out safety programs (commonly required by OSHA).

Figure 16 shows a simple diagram of a hardwire setup with a locking disconnect switch between the power source and the machine.

-16-

SB1037, SB1038, SB1012, SB1015, SB1013 specifications

The Southbend SB1012 is a versatile and efficient commercial range designed specifically for the rigorous demands of professional kitchens. This powerful cooking appliance features a robust construction and advanced technologies that cater to chefs who require precision and reliability in their culinary endeavors.

One of the standout features of the SB1012 is its powerful burners, which come equipped with heavy-duty cast-iron grates. The range typically includes four open burners that deliver exceptional heat output. This allows chefs to achieve quick boiling, searing, and simmering, thereby ensuring perfect cooking results every time. The burners are designed to provide consistent heat distribution, reducing the chance of hot spots and uneven cooking.

The Southbend SB1012 also incorporates a 12-inch griddle, adding another layer of versatility to its functionality. The griddle is constructed from high-quality materials that provide even heat and withstand high temperatures, making it suitable for cooking everything from pancakes to stir-fried dishes. The grease trough and easy-to-clean design contribute to the overall efficiency of the kitchen.

In addition to its cooking surfaces, the SB1012 features a spacious oven compartment, designed to accommodate larger pans and dishes. With a temperature range that typically goes up to 500 degrees Fahrenheit, the oven is ideal for baking, roasting, and other cooking techniques that require precise temperature control. The inclusion of a built-in temperature gauge helps chefs monitor cooking conditions at a glance.

Durability is a hallmark of the Southbend SB1012. The range is constructed from heavy-duty stainless steel, which not only enhances its aesthetic appeal but also ensures resistance to wear and tear in a busy kitchen environment. The removable ovens and easy-access components facilitate straightforward cleaning and maintenance, ensuring the equipment remains in peak condition even after extensive use.

To further improve user experience, the Southbend SB1012 is designed with safety features in mind. The range often includes pilot lights for easy ignition, and the heavy-duty construction minimizes the risk of accidental damage.

In summary, the Southbend SB1012 combines powerful cooking performance with durable construction and ease of use, making it a preferred choice for professional kitchens looking to optimize their cooking capabilities. Its advanced features, versatility, and reliability are tailored to meet the high standards of culinary professionals.