Southbend SB1037, SB1014, SB1015, SB1038, SB1012, SB1013 owner manual Spindle ON/OFF lever-setup

Page 21

For Machines Mfg. Since 7/09

P R E P A R A T I O N

EVS Toolroom Lathes

11.Move the spindle ON/OFF lever to the OFF (center) position, as shown in Figure 22.

Spindle ON/OFF

Lever

Figure 22. Spindle ON/OFF lever-setup.

12.Connect the lathe to power source, then turn the main power switch (Figure 23) to the ON position.

Main

Power

Switch

Figure 23. Main power switch in ON position.

13.Rotate the stop button (Figure 17 on Page 18) clockwise until it pops out. The pump will turn ON. Observe the oil pump tube sight glass (Figure 24). Verify that you see oil flowing out of the tube and against the sight glass.

Oil Pump Sight

Glass and Oil Tube

Figure 24. Oil pump sight glass and oil tube.

Note: This headstock has a pressurized oil system that is equipped with an oil pressure safety switch. If oil stops flowing or does not flow to start with, the lathe will not operate until the oil is properly flowing. Refer to Troubleshooting to correct.

Never bypass the oil pressure safety switch! If you do, you will void the warranty, and headstock damage may occur.

14.Make sure that all bystanders are out of the way, tools are cleared away, and the chuck key is removed from the chuck.

15.Move the spindle ON/OFF lever (Figure

25) down and the chuck will rotate counter- clockwise (down and toward you, as you face the front of the lathe).

Spindle ON/

OFF Lever

Figure 25. Spindle Lever in ON position.

16.Observe the lathe and listen for any abnormal noises or vibration. The lathe should run smoothly with little or no vibration or rubbing noises.

17.Push the stop button. The lathe should stop.

-19-

Image 21
Contents 14 & 16 EVS Toolroom Lathes Customer Service UpdatesScope of Manual Manual FeedbackTable of Contents Accessories About These Machines FeaturesForeword CapabilitiesIdentification Basic Machine Safety Understanding Risks of MachineryTrained/Supervised Operators Only F E T Y Additional Metal Lathe Safety Things Youll Need Preparation OverviewUnpacking Typical preparation process is as followsInventory Main Inventory 1 Figure QtyTool Box Inventory Figure Qty Cleaning & Protecting Before cleaning, gather the followingBasic steps for removing rust preventative Location Cross-Section View of Lifting Setup Lifting & MovingTo lift and move your lathe Leveling Leveling & MountingAssembly Lubricating LatheBolting to Concrete Floors Adding Cutting Fluid Power ConnectionConnecting Power Cord to Lathe Hardwiring Lathe to Power SourceTo connect power cord to the lathe To correct wiring that is out of phase Correcting Out-of-Phase WiringTest Run To test run your machineControl panel-test run Spindle ON/OFF lever-setup E P a R a T I O N To complete the spindle break-in Spindle Break-InFactory adjustments that should be verified Recommended AdjustmentsOperation Overview Main Power Switch Headstock ControlsCarriage Controls Control panel Control PanelTailstock controls Tailstock Controls Foot BrakeItems Needed Qty Removing Chuck or FaceplateTo mount a chuck or faceplate Mounting Chuck or FaceplateTool Needed Qty Installing and Adjusting Camlock StudsCorrect camlock stud alignment Jaw ChuckMounting Workpiece Changing JawsItem Needed Qty To change the jawTo mount a workpiece on the 4-jaw chuck TailstockInstalling Tooling Using QuillTo install tooling in the tailstock Moving Along BedwayOffsetting AligningTo align the tailstock offset to the spindle center line Looking down from above Move tailstock toward Faceplate Mounting Workpiece with ClampsMounting Workpiece Between Centers Mounting Dead Center in Spindle CentersDead Centers Live CentersMounting Center in Tailstock Removing Center from SpindleRemoving Center from Tailstock To mount a center in the tailstockTo install and use the steady rest Steady RestFollow Rest Four-Way Tool Post Compound SlideTo load the tool post To set the compound slide at a certain angleTools Needed Qty Aligning Cutting Tool with Tailstock CenterTo align the cutting tool with the tailstock CenterAdjustable Apron Stop System To adjust the carriage stopCarriage Stop Spindle Speed Manual FeedSetting Spindle Speed Power FeedPower Feed Controls To engage the power feedTo use the quick change feed direction knob Understanding Thread & Feed Rate Chart Positioning Gearbox LeversMod. D.P Normal Position End Gear SetupAlternate Position Configuring End GearsThread Dial & Chart Overview Power Feed LeverThreading Controls Half Nut LeverTPI 4-72 Divisible By Using Thread Dial and ChartTPI 2-54 Not Divisible By Odd Numbered TPIChip Drawer Other Fractional TPI27⁄8 TPI To use the cutting fluid system on your lathe Cutting Fluid SystemHigh-Precision 3-Jaw Scroll Chucks AccessoriesSB1247-MT4 Bull Nose Center SB1279-10 Pc. Precision 5-C Collet SetSBL Gearhead T-Shirt SBL One Good Turn T-Shirt Cleaning Maintenance ScheduleAnnual Service Lubrication Monitoring Oil TemperatureHeadstock Checking & Adding OilTo clean the oil pump system Cleaning Pump System & Changing OilGearbox ApronChanging Oil Lead Screw Lead Screw & Feedrod BearingsWays & Slides Unpainted & Machined SurfacesCleaning Electrical Box Filter To clean the filterBall Oilers End Gearing Annual MaintenanceHandling & Care LubricatingAdding Fluid HazardsTo change the cutting fluid Changing Cutting FluidTo prepare your machine for short-term storage up to a year Machine StorageBacklash Adjustment Compound LeadscrewCross Slide Leadscrew Leadscrew End Play Adjustment Gib AdjustmentTo remove leadscrew end play To adjust the half nut Half Nut AdjustmentTo adjust the clutch release point Feedrod Clutch AdjustmentTo adjust the V-belts Brake & SwitchTo adjust the brake and brake switch BeltsRe-install the pedal stop, tightening it To replace the shear pin Leadscrew Shear Pin ReplacementRe-install the access covers Gap Removal Installation To re-install the gapTo remove the gap TR O U B L E S H O OTI N G TR O U B L E S H O OTI N G TR O U B L E S H O OTI N G Warranty Southbendlathe.com
Related manuals
Manual 144 pages 14.43 Kb

SB1037, SB1038, SB1012, SB1015, SB1013 specifications

The Southbend SB1012 is a versatile and efficient commercial range designed specifically for the rigorous demands of professional kitchens. This powerful cooking appliance features a robust construction and advanced technologies that cater to chefs who require precision and reliability in their culinary endeavors.

One of the standout features of the SB1012 is its powerful burners, which come equipped with heavy-duty cast-iron grates. The range typically includes four open burners that deliver exceptional heat output. This allows chefs to achieve quick boiling, searing, and simmering, thereby ensuring perfect cooking results every time. The burners are designed to provide consistent heat distribution, reducing the chance of hot spots and uneven cooking.

The Southbend SB1012 also incorporates a 12-inch griddle, adding another layer of versatility to its functionality. The griddle is constructed from high-quality materials that provide even heat and withstand high temperatures, making it suitable for cooking everything from pancakes to stir-fried dishes. The grease trough and easy-to-clean design contribute to the overall efficiency of the kitchen.

In addition to its cooking surfaces, the SB1012 features a spacious oven compartment, designed to accommodate larger pans and dishes. With a temperature range that typically goes up to 500 degrees Fahrenheit, the oven is ideal for baking, roasting, and other cooking techniques that require precise temperature control. The inclusion of a built-in temperature gauge helps chefs monitor cooking conditions at a glance.

Durability is a hallmark of the Southbend SB1012. The range is constructed from heavy-duty stainless steel, which not only enhances its aesthetic appeal but also ensures resistance to wear and tear in a busy kitchen environment. The removable ovens and easy-access components facilitate straightforward cleaning and maintenance, ensuring the equipment remains in peak condition even after extensive use.

To further improve user experience, the Southbend SB1012 is designed with safety features in mind. The range often includes pilot lights for easy ignition, and the heavy-duty construction minimizes the risk of accidental damage.

In summary, the Southbend SB1012 combines powerful cooking performance with durable construction and ease of use, making it a preferred choice for professional kitchens looking to optimize their cooking capabilities. Its advanced features, versatility, and reliability are tailored to meet the high standards of culinary professionals.