Grizzly G9972Z Centers, Using a Center in the Spindle, Using a Center in the Tailstock

Centers

I]ZBdYZa<..,'OaVi]Z^cXajYZhVcBI(YZVY XZciZg [dg i]Z iV^ahidX` fj^aa VcY Vc BI) YZVY XZciZg[dgi]Zhe^cYaZ#

BViX]^c\iVeZgh^ci]Zhe^cYaZVcYiV^ahidX`fj^aa egdk^YZ i]Z adX`^c\ VXi^dc [dg ^chiVaa^c\ i]Z XZc" iZgh# 7Z[dgZ ^chZgi^c\ Vcn XZciZg dg VgWdg! bV`Z hjgZ i]Z bVi^c\ hjg[VXZh VgZ eZg[ZXian XaZVc# >[ d^a dg \g^i ^h egZhZci dc i]Z bVi^c\ hjg[VXZh! i]Z iVeZgh l^aa cdi ^ciZgadX` dg l^aa WZ ZmigZbZan Y^[" [^Xjai id gZbdkZ# I]ZhZ eVgih l^aa aVhi adc\ VcY gZbV^cVXXjgViZ^[egdeZganbV^ciV^cZY#

8ZciZgh VgZ bdhi d[iZc ^chiVaaZY ^c i]Z iV^ahidX` fj^aadgjhZYl^i]i]Z[VXZeaViZhZZFigure 22[dg ZmVbeaZh#

Using a Center in the Spindle

1. 9>H8DCC:8IA6I=:;GDBEDL:G

2. I]dgdj\]an XaZVc i]Z bVi^c\ hjg[VXZh d[ i]ZXZciZgVcYhe^cYaZ!i]Zc[^gban^chZgii]Z BI)YZVYXZciZg^cidi]Zhe^cYaZ#

Note: When using the dead center in the spindle, use a lathe dog so that your part will rotate with the spindle.

3. IdgZbdkZi]ZXZciZg[gdbi]Zhe^cYaZ!^chZgi V e^ZXZ d[ gdjcY WVg hidX` dg h^b^aVg idda i]gdj\] i]Z djiWdVgY ZcY d[ i]Z he^cYaZ dc i]Z aZ[i h^YZ d[ i]Z ]ZVYhidX`! i]Zc iVe i]Z XZciZgaddhZ#

Note: Hold onto the center as you tap it loose to avoid it dropping it and damaging the tip or the bedways.

Using a Center in the Tailstock
1. ;ZZY i]Z iV^ahidX` fj^aa dji VWdji &! i]Zc
	^chZgii]ZBI(YZVYXZciZg^cidi]Zfj^aa#
2. Edh^i^dc i]Z iV^ahidX` hd i]Z XZciZg egZhhZh
	V\V^chii]Zldg`e^ZXZ!i]ZcadX`i]ZiV^ahidX`
	^ceaVXZ#
3. ;ZZY i]Z fj^aa VcY YZVY XZciZg ^cid i]Z
	ldg`e^ZXZ!i]ZcadX`i]Zfj^aa^ceaVXZ#
	Note: The force against the mounted
	workpiece will fully seat the center's taper.
4. IdgZbdkZi]ZXZciZg[gdbi]Zfj^aa!]daYdc
Figure 22.8ZciZgh^chiVaaZY^ci]ZiV^ahidX`fj^aa	idi]ZXZciZgl^i]dcZ]VcY!i]ZcgZigVXii]Z
VcYi]Zhe^cYaZl^i]V[VXZeaViZ#	fj^aa WVX` ^cid i]Z iV^ahidX` jci^a i]Z XZciZg
A^kZ XZciZgh VgZ ine^XVaan Wj^ai l^i] WZVg^c\h VcY	edeh[gZZ#
he^cYjg^c\jhZ!hdi]ZnYdcdicZZYajWg^XVi^dc#
=dlZkZg! YZVY XZciZgh Yd cdi he^c Yjg^c\ jhZ
VcYgZfj^gZi]Zi^eidWZXdchiVcianajWg^XViZYl^i]
Vci^"hZ^oZ\gZVhZ#
NOTICE

To avoid premature wear of the dead center or damage to the workpiece, always keep the dead center tip well lubricated during use.

<..,'O&&m'+AVi]Zl$<ZVgWdm "'("