Grizzly G9972Z owner manual Feed Rate, 8Vc\Z ZVgb, #%%.%, #%%%, #%&*%

Feed Rate

;ZZYgViZ^hi]ZheZZYi]ZiddaigVkZahYjg^c\i]Z deZgVi^dcVcY^hZmegZhhZY^c^cX]Zhd[XVgg^V\Z igVkZa eZg gZkdaji^dc d[ i]Z he^cYaZ >EG! VcY ^h hZiWnXdc[^\jg^c\i]ZX]Vc\Z\ZVghVcY[ZZYgViZ Y^Vah#

I]Z XdggZXi [ZZY gViZ ^h YZiZgb^cZY Wn i]Z ldg`e^ZXZbViZg^Va!i]ZineZd[idda^c\jhZY!VcY i]ZYZh^gZY[^c^h]#I]ZiVWaZ^cFigure 40 h]dlh i]ZgZXdbbZcYZY[ZZYgViZ[dgijgc^c\bdhibZi" Vah#

Recommended Feed Rates

	Idda;ZZYGViZ>EG
Ldg`BViZg^Va	Rough Cuts	Finish Cuts
BV\cZh^jb	%#%&*¶%#%'*	%#%%*¶%#%&%
6ajb^cjb	%#%&*¶%#%'*	%#%%*¶%#%&%
7gVhh7gdcoZ	%#%&*¶%#%'*	%#%%(¶%#%&%
8deeZg	%#%&%¶%#%'%	%#%%)¶%#%%-
8Vhi>gdcHd[i	%#%&*¶%#%'*	%#%%*¶%#%&%
8Vhi>gdc=VgY	%#%&%¶%#%'%	%#%%(¶%#%&%
B^aYHiZZa	%#%&%¶%#%'%	%#%%(¶%#%&%
8VhiHiZZa	%#%&%¶%#%'%	%#%%(¶%#%&%
6aadnHiZZah=VgY	%#%&%¶%#%'%	%#%%(¶%#%&%
IddaHiZZa	%#%&%¶%#%'%	%#%%(¶%#%&%
HiV^caZhhHiZZa	%#%&%¶%#%'%	%#%%(¶%#%&%
I^iVc^jb	%#%&%¶%#%'%	%#%%(¶%#%&%
=^BV\VcZhZHiZZa	%#%&%¶%#%'%	%#%%(¶%#%&%

Note: These values are a guideline only. Refer to the MACHINERY’S HANDBOOK for more detailed information.

Figure 40.GZXdbbZcYZY[ZZYgViZiVWaZ#

The V-belt, change gears, and pulleys represent a serious entanglement hazard when the lathe is running. Always dis- connect the lathe from power before opening the change gear cover.

JhZ Figure 41 id ^YZci^[n i]Z X]Vc\Z \ZVgh VcY i]Z^gedh^i^dch#

Note: This lathe is shipped with the 24 tooth gear installed in the "a" position, and the 84 tooth gear in the "b" position.

8]Vc\Z<ZVg8]Vc\Z

&'%$&',I <ZVga

E^kdi6gb 8VeHXgZl

8]Vc\Z <ZVgb

Figure 41.8]Vc\Z\ZVgh#

V

&'%

W

)*	^ch$	V	W	aZkZg			8	6	7
		')	-)		>>		%#%%''	%#%%)*	%#%%.%
)*
		'-	,%		>>		%#%%(%	%#%%+%	%#%&'%
&',
		'-	,,			>	%#%%((	%#%%+,	%#%&(*
		(*	,%				%#%%(-	%#%%,,	%#%&*%
					>>

Figure 42.;ZZYgViZX]Vgi[dgedlZg[ZZYbdkZbZcid[i]ZXVgg^V\Z#

"('" <..,'O&&m'+AVi]Zl$<ZVgWdm